Difference between revisions of "OpenWRT: Setup OLSR di UBNT via CLI"

From OnnoWiki
Jump to navigation Jump to search
 
(26 intermediate revisions by the same user not shown)
Line 49: Line 49:
 
  config wifi-device  radio0
 
  config wifi-device  radio0
 
         option type    mac80211
 
         option type    mac80211
         option channel  1
+
         '''option channel  1'''
 
         option hwmode  11g
 
         option hwmode  11g
 
         txpower        15
 
         txpower        15
         option path    'platform/ar231x-wmac.0'
+
         option path    'platform/ar231x-wmac.0'  '''# option path berbeda untuk NS2 NSM2 Bullet dll'''
 
   
 
   
 
         # REMOVE THIS LINE TO ENABLE WIFI:
 
         # REMOVE THIS LINE TO ENABLE WIFI:
         option disabled 0
+
         '''option disabled 0'''
 
   
 
   
 
  config wifi-iface
 
  config wifi-iface
 
         option device  radio0
 
         option device  radio0
         option network  mesh
+
         '''option network  MESH'''
         option mode    adhoc
+
         '''option mode    adhoc'''
         option ssid    MESH
+
         '''option ssid    MESH'''
 
         option encryption none
 
         option encryption none
         option bssid    02:CA:FF:EE:BA:BE
+
         '''option bssid    02:CA:FF:EE:BA:BE'''
  
  
Line 87: Line 87:
 
         option netmask  255.255.255.0
 
         option netmask  255.255.255.0
 
   
 
   
  config interface mesh
+
'''# konfigurasi berikut penting untuk MESH'''
        option ifname  wlan0
+
'''#'''
        option type    bridge
+
  config interface 'MESH'
        option proto   static
+
option _orig_ifname 'wlan0'
        option ipaddr  10.123.123.223 '''(SETIAP NODE HARUS menggunakan IP yang BEDA!!)'''
+
option _orig_bridge 'false'
        option netmask  255.255.255.0
+
option proto 'static'
 +
        option ipaddr  10.123.123.223 '''# (SETIAP NODE HARUS menggunakan IP yang BEDA!!)'''
 +
        option netmask  255.0.0.0
 +
 
 +
==Setup NAT melalui MESH==
 +
 
 +
Sebaiknya buat setup Firewall
 +
 
 +
rm /etc/config/firewall
 +
 
 +
Buat [[NAT]] di /etc/rc.local saja
  
==Set agar OLSR start waktu booting==
+
==Set agar [[NAT]] dan [[OLSR]] start waktu booting==
  
 
Edit rc.local
 
Edit rc.local
Line 102: Line 112:
 
Isi
 
Isi
  
 +
ifconfig wlan0 10.123.123.223 netmask 255.0.0.0 '''(IP ADDRESS sama dengan IP addres di /etc/config/network  di ATAS)'''
 +
echo 1 > /proc/sys/net/ipv4/ip_forward
 +
iptables -t nat -A POSTROUTING -o wlan0 -j MASQUERADE
 +
/etc/init.d/telnet stop
 
  /etc/init.d/olsrd stop
 
  /etc/init.d/olsrd stop
 
  olsrd -f /etc/olsrd.conf &
 
  olsrd -f /etc/olsrd.conf &
 +
 +
exit 0
  
exit 0
+
 
 +
Nampaknya [[NAT]] sebaiknya di aktifkan di rc.local.
 +
Semua setting /etc/config/firewall di matikan agar [[OLSR]] tidak rewel.
  
 
==Buat file /etc/olsrd.conf==
 
==Buat file /etc/olsrd.conf==
Line 115: Line 133:
 
Isi dengan
 
Isi dengan
  
 +
# DebugLevel 0
 +
# AllowNoInt yes
 +
# IpVersion 4
 +
# RtTable 111
 +
# RtTableDefault 112
 +
 
  Hna4
 
  Hna4
 
  {
 
  {
 +
# 0.0.0.0 0.0.0.0            # JIKA INGIN memberitahukan bahwa kita adalah gateway ke Internet
 +
# 192.168.0.0 255.255.255.0  # JIKA INGIN memberitahukan kita gateway ke 192.168.0.0/24
 
  }
 
  }
 
   
 
   
 
  Hna6
 
  Hna6
 
  {
 
  {
  }
+
  }  
 
   
 
   
  LoadPlugin "olsrd_nameservice.so.0.3"
+
  LoadPlugin "olsrd_arprefresh.so.0.1"
 
  {
 
  {
 
  }
 
  }
 
   
 
   
  LoadPlugin "olsrd_txtinfo.so.0.1"
+
  LoadPlugin "olsrd_nameservice.so.0.3"
 
  {
 
  {
    PlParam "accept" "0.0.0.0"
+
        '''PlParam "name" "NAMA-NODE-Mesh-ini"'''
 +
        PlParam "latlon-file" "/var/run/latlon.js"
 +
        PlParam "hosts-file" "/var/etc/hosts.olsr"
 +
        PlParam "sighup-pid-file" "/var/run/dnsmasq.pid"
 +
        PlParam "services-file" "/var/run/services_olsr"
 +
        PlParam "suffix" ".olsr"
 
  }
 
  }
 
   
 
   
  InterfaceDefaults
+
LoadPlugin "olsrd_txtinfo.so.0.1" 
 +
{                                   
 +
        PlParam "accept" "0.0.0.0" 
 +
}                                   
 +
                                                 
 +
LoadPlugin "olsrd_watchdog.so.0.1"               
 +
{                                                     
 +
        PlParam "file" "/var/run/olsrd.watchdog"       
 +
        PlParam "interval" "30"                       
 +
}                                                     
 +
                                                       
 +
LoadPlugin "olsrd_jsoninfo.so.0.0"                     
 +
{                                                     
 +
}                                                     
 +
                                 
 +
  InterfaceDefaults                
 +
{                               
 +
        Ip4Broadcast 255.255.255.255
 +
}                                             
 +
                                               
 +
Interface "wlan0"                             
 
  {
 
  {
  }
+
        mode mesh
   
+
  }  
Interface "wlan0"
+
 
{
+
 
    Mode "mesh"
+
Daftar lengkap olsrd plugin yang ada bisa dilihat di
}
+
 
 +
  /usr/lib
 +
 
 +
==Pranala Menarik==
 +
 
 +
* [[OpenWRT]]
 +
* [[OpenWRT: Download Firmware yang sudah jadi]]
 +
* [[OpenWRT: Source Repository Download]]
 +
* [[OpenWRT: Melihat Daftar Package]]
 +
* [[OpenWRT: Mengembalikan setting default Config.in]]
 +
 
 +
===Build Firmware===
 +
 
 +
* [[OpenWRT: Build Firmware]]
 +
* [[OpenWRT: Build Firmware Download Source Pendukung]]
 +
* [[OpenWRT: Build Firmware Buffalo WZRHPG450H]]
 +
* [[OpenWRT: Build Firmware Buffalo WZRHPG300N]]
 +
* [[OpenWRT: Build Firmware Buffalo WZRHPG300NH2]]
 +
* [[Buffalo]]
 +
* [[Buffalo: WZRHPG450H Cara Recovery]]
 +
* [[Buffalo: WZRHPG450H OpenWRT mengaktifkan setelah di flash]]
 +
* '''[[Buffalo: WZRHPG450H Membuat Firmware OpenWRT Sendiri]]''' '''RECOMMENDED'''
 +
* [[Buffalo: WZRHPG450H OpenWRT instalasi aplikasi Pendukung OLSRD]]
 +
* [[OpenWRT: Build Firmware Ubiquiti NanoStation2]] '''RECOMMENDED'''
 +
* [[OpenWRT: Build Firmware Ubiquiti NanoStationM2]] '''RECOMMENDED'''
 +
* [[OpenWRT: Build Firmware Mikrotik RB433]]
 +
* [[OpenWRT: Build Firmware Linksys WRT160NL]]
 +
* [[OpenWRT: Build Firmware Linksys WRT54GL]]
 +
 
 +
===APRX===
 +
 
 +
 
 +
* [[OpenWRT: Build Firmware Buffalo WZRHPG300NH2 untuk APRX]]
 +
* [[OpenWRT: Setup APRX]]
 +
 
 +
===IPv6===
 +
 
 +
* [[OpenWRT: IPv6]]
 +
* [[OpenWRT IPv6: Build Firmware Linksys WRT160NL]]
 +
* [[OpenWRT IPv6: Build Firmware Linksys WRT160NL Tanpa WebGUI]]
 +
* [[OpenWRT IPv6: Build Firmware Buffalo WZRHPG450H]]
 +
* [[OpenWRT IPv6: Build Firmware Buffalo WZRHPG300NH2]]
 +
* [[OpenWRT IPv6: Setup tunnel ke tunnelbroker]]
 +
* [[OpenWRT IPv6: Konfigurasi]]
 +
* [[OpenWRT IPv6: Konfigurasi WAN6 dengan radvd]]
 +
 
 +
===Flash Firmware===
 +
 
 +
* [[OpenWRT: Flash Linksys WRT54GL]]
 +
* [[OpenWRT: Flash Linksys WRT160NL]]
 +
* [[OpenWRT: Flash Buffalo WZRHP450H]] '''RECOMMENDED'''
 +
* [[OpenWRT: Flash Buffalo WZRHP300N]]
 +
* [[OpenWRT: Flash UBNT NanoStation2]] '''RECOMMENDED'''
 +
* [[OpenWRT: Flash UBNT NanoStation M2]] '''RECOMMENDED'''
 +
* [[OpenWRT: Flash UBNT NanoStation Loco M2]]
 +
* [[OpenWRT: Flash UBNT Bullet M2]] '''RECOMMENDED'''
 +
* [[OpenWRT: Flash Mikrotik RB433]] '''RECOMMENDED'''
 +
* [[OpenWRT: Flash Mikrotik RB450]]
 +
 
 +
===Misc===
 +
 
 +
* [[OpenWRT: CLI]]
 +
* [[OpenWRT: Setup WiFi]]
 +
* [[OpenWRT: Setup PPTP VPN Server]]
 +
* [[OpenWRT: Setup OLSR di UBNT via CLI]] '''RECOMMENDED'''
 +
* [[OpenWRT: Mikrotik RB433]] '''RECOMMENDED'''
 +
* [[OpenWRT: Setup OLSR Sederhana]]
 +
* [[OpenWRT: Setup OLSR via Web]] '''RECOMMENDED'''
 +
* [[OLSR - di OpenWRT]]
 +
* [[OpenWRT: 3G modem]]
 +
* [[OpenWRT: Build Firmware dengan 3G Modem Support]]
 +
* [[OpenWRT: Setup Firewall]]
 +
* [[OpenWRT: Konfigurasi UBNT NanoStation2 tanpa WebGUI]]
 +
* [[OpenWRT: OLSR nameservice plugin]]
 +
* [[OpenWRT: VLAN]]
 +
 
 +
===UBNT===
 +
 
 +
* [[UBNT]]
 +
* [[UBNT: Teknik Recovery]]
 +
* [[UBNT: Upload Firmware]]
 +
* [[UBNT: Rebuild Firmware]]
 +
* [[UBNT: firmware dengan OLSR]]25
 +
* [[UBNT: openwrt]]
 +
* [[UBNT: olsr dengan openwrt]]
 +
* [[UBNT: olsr dengan kamikaze openwrt]]
 +
* [[UBNT: olsr dengan backfire openwrt]]
 +
* [[UBNT: UniFi]]
 +
* [[UBNT: UniFi Konfigurasi Awal]]
 +
* [[UBNT: UniFi Manajemen HotSpot]]
 +
* [[UBNT: OLSR Pembuatan Firmware]]
 +
* [[UBNT: OLSR Konfigurasi]]
 +
* [[OLSR - di UBNT]]
 +
* [[OLSR - di Ubuntu]]
 +
* [[OpenWRT]]
 +
* [[OLSR: NAT di UBNT dengan OLSR]]

Latest revision as of 05:54, 27 February 2014

Reset Password Root

Reset password root melalui telnet ke 192.168.1.1

telnet 192.168.1.1

Tampilan

Trying 192.168.1.1...
Connected to 192.168.1.1.
Escape character is '^]'.
 === IMPORTANT ============================
  Use 'passwd' to set your login password
  this will disable telnet and enable SSH
 ------------------------------------------


BusyBox v1.19.4 (2013-04-10 18:38:45 WIT) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 BARRIER BREAKER (Bleeding Edge, r36235)
 -----------------------------------------------------
  * 1/2 oz Galliano         Pour all ingredients into
  * 4 oz cold Coffee        an irish coffee mug filled
  * 1 1/2 oz Dark Rum       with crushed ice. Stir.
  * 2 tsp. Creme de Cacao
 -----------------------------------------------------

root@OpenWrt:/# passwd
Changing password for root
New password:
Retype password:
Password for root changed by root

Konfigurasi Wireless

Konfigurasi wireless dan mengaktifkan sebagai adhoc pada channel 1.

vi /etc/config/wireless

Isinya kira-kira

config wifi-device  radio0
        option type     mac80211
        option channel  1
        option hwmode   11g
        txpower         15
        option path     'platform/ar231x-wmac.0'  # option path berbeda untuk NS2 NSM2 Bullet dll

        # REMOVE THIS LINE TO ENABLE WIFI:
        option disabled 0

config wifi-iface
        option device   radio0
        option network  MESH
        option mode     adhoc
        option ssid     MESH
        option encryption none
        option bssid    02:CA:FF:EE:BA:BE


Konfigurasi IP address MESH

Set IP statik melalui perintah

vi /etc/config/network

Isi kira-kira

config interface loopback
        option ifname   lo
        option proto    static
        option ipaddr   127.0.0.1
        option netmask  255.0.0.0 

config interface lan
        option ifname   eth0
        option type     bridge
        option proto    static
        option ipaddr   192.168.1.1
        option netmask  255.255.255.0

# konfigurasi berikut penting untuk MESH
#
config interface 'MESH'
	option _orig_ifname 'wlan0'
	option _orig_bridge 'false'
	option proto 'static'
       option ipaddr   10.123.123.223 # (SETIAP NODE HARUS menggunakan IP yang BEDA!!)
       option netmask  255.0.0.0

Setup NAT melalui MESH

Sebaiknya buat setup Firewall

rm /etc/config/firewall

Buat NAT di /etc/rc.local saja

Set agar NAT dan OLSR start waktu booting

Edit rc.local

vi /etc/rc.local

Isi

ifconfig wlan0 10.123.123.223 netmask 255.0.0.0 (IP ADDRESS sama dengan IP addres di /etc/config/network  di ATAS)
echo 1 > /proc/sys/net/ipv4/ip_forward
iptables -t nat -A POSTROUTING -o wlan0 -j MASQUERADE
/etc/init.d/telnet stop
/etc/init.d/olsrd stop
olsrd -f /etc/olsrd.conf &

exit 0


Nampaknya NAT sebaiknya di aktifkan di rc.local. Semua setting /etc/config/firewall di matikan agar OLSR tidak rewel.

Buat file /etc/olsrd.conf

Edit

vi /etc/olsrd.conf

Isi dengan

# DebugLevel 0
# AllowNoInt yes
# IpVersion 4
# RtTable 111
# RtTableDefault 112

Hna4
{
# 0.0.0.0 0.0.0.0            # JIKA INGIN memberitahukan bahwa kita adalah gateway ke Internet
# 192.168.0.0 255.255.255.0  # JIKA INGIN memberitahukan kita gateway ke 192.168.0.0/24
}

Hna6
{
} 

LoadPlugin "olsrd_arprefresh.so.0.1"
{
}

LoadPlugin "olsrd_nameservice.so.0.3"
{
        PlParam "name" "NAMA-NODE-Mesh-ini"
        PlParam "latlon-file" "/var/run/latlon.js"
        PlParam "hosts-file" "/var/etc/hosts.olsr"
        PlParam "sighup-pid-file" "/var/run/dnsmasq.pid"
        PlParam "services-file" "/var/run/services_olsr"
        PlParam "suffix" ".olsr"
}

LoadPlugin "olsrd_txtinfo.so.0.1"   
{                                    
        PlParam "accept" "0.0.0.0"   
}                                    
                                                  
LoadPlugin "olsrd_watchdog.so.0.1"                
{                                                       
        PlParam "file" "/var/run/olsrd.watchdog"        
        PlParam "interval" "30"                         
}                                                       
                                                        
LoadPlugin "olsrd_jsoninfo.so.0.0"                      
{                                                       
}                                                       
                                  
InterfaceDefaults                 
{                                 
        Ip4Broadcast 255.255.255.255
}                                               
                                               
Interface "wlan0"                               
{
        mode mesh
} 


Daftar lengkap olsrd plugin yang ada bisa dilihat di

/usr/lib

Pranala Menarik

Build Firmware

APRX

IPv6

Flash Firmware

Misc

UBNT