Difference between revisions of "OpenWRT: Flash Mikrotik RB433"

Revision as of 05:22, 19 December 2013

Installation overview

Gambaran umum tiga langkah cara instalasi:

Boot board dengan OpenWrt dari jaringan (netboot): server DHCP dan TFTP dibutuhkan di host.
Instal OpenWrt ke internal flash dengan wget2nand: server HTTP atau FTP dibutuhkan di host.
Reboot dengan instalasi baru, lakukan konfigurasi dll.

Netboot

bootloader dari RB433 mampu untuk meload image dalam format elf melalui BOOTP ke RAM dan menjalankannya.

Build Image

Kita perlu mendownload OpenWrt trunk. Di menuconfig pilih:

Target System: Atheros AR7xxx/AR9xxx
Subtarget: Devices with NAND flash (mostly Mikrotik)
Target Images: ramdisk (juga tar.gz jika kita berencana untuk menginstalasi secara permanen dengan image yang sama).

Buat versi ram disk. Jika sudah ada binary-nya, buat symlink atau copy ke directory tftp-root, misalnya.

sudo mkdir -p /tftpboot
# sudo ln -sf $(HOME)/openwrt/rb433uah-netboot/bin/ar71xx/openwrt-ar71xx-nand-vmlinux-initramfs.elf /tftpboot/openwrt.elf
cp openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf /tftpboot/openwrt.elf
chmod -Rf 777 /tftpboot/

Setup Host

Kita membutuhkan server BOOTP dan TFTP di host, yang paling mudah adalah menggunakan dnsmasq, karena dapat memberikan dua layanan tersebut sekaligus. Install menggunakan perintah:

sudo apt-get install dnsmasq

Ubah dnsmasq.conf

vi /etc/dnsmasq.conf

Misalnya menggunakan parameter

interface=eth0
dhcp-range=192.168.0.50,192.168.0.150,12h
# dhcp-host=00:0C:42:XX:XX:XX,192.168.6.101 # ubah menggunakan MAC board Mikrotik yang kita gunakan
dhcp-host=00:0C:42:72:E0:41,192.168.0.100
enable-tftp
tftp-root=/tftpboot
dhcp-boot=/tftpboot/openwrt.elf,boothost,192.168.0.6

Restart dnsmasq

/etc/init.d/dnsmasq restart

Jika diperlukan kita dapat menset IP dari interface secara manual, misalnya:

sudo ip addr add 192.168.0.1/24 dev eth0
sudo ifconfig eth0 192.168.0.1

Setup Target

Install

apt-get install screen

Sambunkan kabel serial. Jalankan di terminal

screen /dev/ttyUSB0 115200,cs8,-ixon,-ixoff

Langkah yang perlu dilakukan:

Sambungkan ke serial port dengan kabel serial (115200, 8N1).
Tekan tombol apapun setelah board dinyalakan.
Tekan o to change the boot device
Tekan e to boot from ethernet in the future.
Tekan x untk keluar dari setup (-o-e-x is needed only once, the boot method is saved in non-volatile memory)
CATATAN: untuk mengembalikan boot ke NAND tekan -o-o-x

RouterBOOT booter 3.02

RouterBoard 433AH

CPU frequency: 680 MHz
  Memory size: 128 MiB
    NAND size: 128 MiB

Press any key within 2 seconds to enter setup..

Jika semua benar akan tampak kira-kira seperti:

RouterBOOT booter 2.16

RouterBoard 433AH

CPU frequency: 680 MHz
  Memory size: 128 MB

Press any key within 2 seconds to enter setup..
trying bootp protocol.......... OK
Got IP address: 192.168.6.101
resolved mac address 4E:80:00:00:00:00
Gateway: 192.168.6.1
transfer started ................................... transfer ok, time=7.16s
setting up elf image... OK
jumping to kernel code
Linux version 2.6.26.7 (joerga@thinkpad) (gcc version 4.1.2) #2 Mon Nov 10 11:23:37 CET 2008
console [early0] enabled
...

Instalasi Permanen

Untuk melakukan instalasi permanen, kita perlu masuk menggunakan netboot. Kita tidak bisa me-reflash dari instalasi OpenWRT sebelumnya, flash hanya bisa dilakukan melalui netboot.

Target Image

File yang dperlukan untuk me-flas NAND adalah

openwrt-ar71xx-nand-rootfs.tar.gz
openwrt-ar71xx-nand-vmlinux-lzma.elf

Save your RouterOS license key

If you have access to the MikroTik's Winbox software, you can export the license file from System→Licence, as stated on the RouterBoard 411 page.

Otherwise, boot RouterOS and export the key to a file:

/system license output

Then list the files on your device to see which file the .key file was saved:

/file print

On a fresh install, the key file should be #1 (or #0 on a RB433UAH); to open the editor with file #1, type:

/file edit 1 value-name=contents

Then copy-paste the text in a file on your computer. The differences between the obtained key file and a key exported with Winbox are that the SoftwareID line is not present in the latter, and there are no empty lines, so you should probably delete all the empty lines in your file prior to import it for a new installation; the SoftwareID line should not bother the installer (untested).

Erase the NAND Flash

Jika kita ingin menginstalasi OpenWRT secara perman ke NAND flash. Kita perlu memformat NAND flash untuk membuang semua RouterOS.

Caranya:

Sambung melalui serial.
Tekan keyboard setelah RB433 nyala.
Tekan e dan ketik yes untuk memformat flash dari bootloader.

Setup the Host

An HTTP web server is required on the host, e.g. mini-httpd in Ubuntu. Install the mini-httpd web server

sudo apt-get install mini-httpd

In /etc/default/mini-httpd change

   Start daemon

   START=1

In /etc/mini-httpd.conf change

   On which host mini_httpd should bind

host=192.168.6.1

   Run in chroot mode

chroot

   Where are the web files stored

data_dir=/home/openwrt/rb433uah/bin/ar71xx/

Restart the mini-httpd web server

sudo /etc/init.d/mini-httpd restart

Install OpenWrt into Flash

   Start netboot (see above).
   Press ENTER to get a shell prompt.
   Execute:

wget2nand http://192.168.6.1

This script will set an IP address via dhcp on br-lan. The output should look like:

root@OpenWrt:/# wget2nand http://192.168.6.254
Connecting to 192.168.6.254 (192.168.6.254:80)
kernel               100% |*******************************|  1041k  0:00:00 ETA
Connecting to 192.168.6.254 (192.168.6.254:80)
rootfs.tgz           100% |*******************************|  4243k  0:00:00 ETA
Erasing filesystem...
[  137.110000] nand_erase_nand: attempt to erase a bad block at page 0x00002240
[  137.140000] nand_erase_nand: attempt to erase a bad block at page 0x00003ac0
[  137.180000] nand_erase_nand: attempt to erase a bad block at page 0x00005d40
[  137.620000] nand_erase_nand: attempt to erase a bad block at page 0x00026a80
[  137.850000] nand_erase_nand: attempt to erase a bad block at page 0x000373c0
[  137.860000] nand_erase_nand: attempt to erase a bad block at page 0x00037440
[  138.000000] yaffs: dev is 32505861 name is "mtdblock5" rw
[  138.000000] yaffs: passed flags ""
[  138.020000] yaffs: dev is 32505862 name is "mtdblock6" rw
[  138.020000] yaffs: passed flags ""
Mounting /dev/mtdblock6 as new root and /dev/mtdblock5 as kernel partition
Copying kernel...
Preparing filesystem...
./
./tmp/
./usr/
./usr/lib/
./usr/lib/opkg/
…
./proc/
./sys/
./www/
./root/
./var
Cleaning up...
Image written, you can now reboot.  Remember to change the boot source to Boot from Nand

Reboot the RB433 and change the boot source to NAND.

USB Ports

To have the USB ports work on the RB433UAH, you need to install the kmod-usb2 package, as explained on the USB Basic Support page. See also the USB Overview page.

Referensi

Pranala Menarik

Build Firmware

APRX

OpenWRT: Build Firmware Buffalo WZRHPG300NH2 untuk APRX

IPv6

Flash Firmware

OpenWRT: Flash Linksys WRT54GL
OpenWRT: Flash Linksys WRT160NL
OpenWRT: Flash Buffalo WZRHP450H RECOMMENDED
OpenWRT: Flash Buffalo WZRHP300N
OpenWRT: Flash UBNT NanoStation2 RECOMMENDED
OpenWRT: Flash UBNT NanoStation M2 RECOMMENDED
OpenWRT: Flash UBNT NanoStation Loco M2
OpenWRT: Flash UBNT Bullet M2 RECOMMENDED
OpenWRT: Flash Mikrotik RB433 RECOMMENDED
OpenWRT: Flash Mikrotik RB450