Difference between revisions of "OpenBTS: E110 Install Image di MicroSD"

From OnnoWiki
Jump to navigation Jump to search
 
(7 intermediate revisions by the same user not shown)
Line 58: Line 58:
  
 
  /dev/sdb
 
  /dev/sdb
 +
 +
Jika perlu kita buang semua partisi yang ada menggunakan fdisk
 +
 +
fdisk /dev/sdb
 +
d 1
 +
d 2
 +
q
  
 
Gunakan 'MakeEttusSDCard.sh' yang akan mengurus partisi dll.
 
Gunakan 'MakeEttusSDCard.sh' yang akan mengurus partisi dll.
Line 63: Line 70:
 
  cd /usr/local/src/e1xx-003
 
  cd /usr/local/src/e1xx-003
 
  sudo ./MakeEttusSDCard.sh /dev/sdb
 
  sudo ./MakeEttusSDCard.sh /dev/sdb
 +
 +
Keluaran akan kira-kira
 +
 +
..
 +
..
 +
Populating boot partition files
 +
Boot partition complete
 +
Populating rootfs partition files
 +
This will take several minutes . . .
 +
Rootfs partition complete
 +
SD card creation was successful
  
 
Ini akan membutuhkan waktu lumayan lama, jika selesai maka akan melaporkan sukses.
 
Ini akan membutuhkan waktu lumayan lama, jika selesai maka akan melaporkan sukses.
Line 202: Line 220:
  
 
* [[OpenBTS]]
 
* [[OpenBTS]]
 +
* [[OpenBTS: Arsitektur secara umum]]
  
 
===Persiapan===
 
===Persiapan===
Line 209: Line 228:
 
* [[USRP: Kalibrasi ClockTamer]]
 
* [[USRP: Kalibrasi ClockTamer]]
 
* [[USRP: ClockTamer Control Protocol]]
 
* [[USRP: ClockTamer Control Protocol]]
 +
* [[USRP: ClockTamer Flashing]]
 
* [[USRP: Instalasi Board]]
 
* [[USRP: Instalasi Board]]
 
* [[OpenBTS: GIT Source Code]]
 
* [[OpenBTS: GIT Source Code]]
 
* [[USRP: Rangkaian Board USRP]]
 
* [[USRP: Rangkaian Board USRP]]
 
* [[OpenBTS: Tethr untuk Bencana Alam]]
 
* [[OpenBTS: Tethr untuk Bencana Alam]]
 +
* [[USRP: Tip Pemesanan]]
 +
 +
===Script===
 +
 +
* [[OpenBTS: Script Membuat GNURadio 3.4.2 di Ubuntu 13.04]]
 +
* [[OpenBTS: Script Membuat OpenBTS dan yate di Ubuntu 13.04]]
 +
* [[OpenBTS: Script Membuat OpenBTS 2.8.0 di RangeNetwork Dev Kit]]
 +
* [[OpenBTS: Script Membuat OpenBTS di RangeNetwork Dev Kit]]
  
 
===OpenBTS 2.6===
 
===OpenBTS 2.6===
Line 221: Line 249:
 
* [[GNURadio: Ubuntu Install GNURadio 3.4.2]] '''RECOMMENDED'''
 
* [[GNURadio: Ubuntu Install GNURadio 3.4.2]] '''RECOMMENDED'''
 
* [[GNURadio: Ubuntu Install GNURadio 3.4.2 Clock 52MHz]] '''RECOMMENDED'''
 
* [[GNURadio: Ubuntu Install GNURadio 3.4.2 Clock 52MHz]] '''RECOMMENDED'''
 +
* [[GNURadio: Ubuntu 13.04 Install GNURadio 3.4.2 Clock 52MHz]] ''NOT RECOMMENDED''
 
* [[GNURadio: Contoh Aplikasi]]
 
* [[GNURadio: Contoh Aplikasi]]
 
* [[GNURadio: Spectrum Analizer GSM]]
 
* [[GNURadio: Spectrum Analizer GSM]]
Line 227: Line 256:
 
* [[OpenBTS: Ubuntu Install]] '''RECOMMENDED'''
 
* [[OpenBTS: Ubuntu Install]] '''RECOMMENDED'''
 
* [[OpenBTS: Ubuntu Install OpenBTS 2.6 Clock 52MHz]] '''RECOMMENDED'''
 
* [[OpenBTS: Ubuntu Install OpenBTS 2.6 Clock 52MHz]] '''RECOMMENDED'''
 +
* [[OpenBTS: Ubuntu 13.04 Install OpenBTS 2.6 Clock 52MHz]] ''NOT RECOMMENDED''
 
* [[OpenBTS: Konfigurasi]] '''RECOMMENDED'''
 
* [[OpenBTS: Konfigurasi]] '''RECOMMENDED'''
 
* [[OpenBTS: Kalibrasi]]
 
* [[OpenBTS: Kalibrasi]]
Line 247: Line 277:
 
* [[GNURadio: Install UHD]]
 
* [[GNURadio: Install UHD]]
 
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.3.0]]
 
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.3.0]]
 +
* [[GNURadio: Ubuntu 12.10 Instal GNURadio 3.3.0]]
 +
* [[GNURadio: Ubuntu 12.10 Instal GNURadio 3.4.1]] ''NOT RECOMMENDED''
 
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.4.2]] '''RECOMMENDED'''
 
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.4.2]] '''RECOMMENDED'''
 
* [[GNURadio: Ubuntu 12.04 Instal GNURadio 3.4.2]] '''RECOMMENDED'''
 
* [[GNURadio: Ubuntu 12.04 Instal GNURadio 3.4.2]] '''RECOMMENDED'''
 +
* [[GNURadio: Ubuntu 12.04.1 Instal GNURadio 3.4.2]] '''RECOMMENDED'''
 +
* [[GNURadio: Ubuntu 12.10 Instal GNURadio 3.4.2]] ''NOT RECOMMENDED''
 +
* [[GNURadio: Ubuntu 13.04 Instal GNURadio 3.4.2]] '''RECOMMENDED'''
 
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.5.0]] ''NOT RECOMMENDED''
 
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.5.0]] ''NOT RECOMMENDED''
 
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.5.3.2]] ''NOT RECOMMENDED''
 
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.5.3.2]] ''NOT RECOMMENDED''
Line 254: Line 289:
 
* [[GNURadio: Ubuntu 11.10 Install dari GIT GNURadio]] ''NOT RECOMMENDED''
 
* [[GNURadio: Ubuntu 11.10 Install dari GIT GNURadio]] ''NOT RECOMMENDED''
 
* [[GNURadio: Ubuntu 11.10 cek USRP Daughter Board]]
 
* [[GNURadio: Ubuntu 11.10 cek USRP Daughter Board]]
* [[GNURadio: UHD]]
+
* [[GNURadio: UHD]] ''NOT RECOMMENDED''
* [[GNURadio: UHD Image]]
+
* [[GNURadio: UHD Image]] ''NOT RECOMMENDED''
 +
* [[GNURadio: UHD burn EEPROM RFX Board di USRP1]] ''NOT RECOMMENDED''
 
* [[GNURadio: UHD Identifikasi Device]]
 
* [[GNURadio: UHD Identifikasi Device]]
 
* [[OpenBTS: Ubuntu 11.10 Install]]
 
* [[OpenBTS: Ubuntu 11.10 Install]]
Line 261: Line 297:
 
* [[OpenBTS: 2.8 dari SVN Install]]
 
* [[OpenBTS: 2.8 dari SVN Install]]
 
* [[OpenBTS: 2.8 dari SVN Install Clock 52MHz]] '''RECOMMENDED'''
 
* [[OpenBTS: 2.8 dari SVN Install Clock 52MHz]] '''RECOMMENDED'''
 +
* [[OpenBTS: 2.8 dari SVN Install Clock 52MHz di Ubuntu 12.10]] '''RECOMMENDED'''
 +
* [[OpenBTS: 2.8 dari SVN Install Clock 52MHz di Ubuntu 13.04]] '''RECOMMENDED'''
 +
* [[OpenBTS: 2.8 dari SVN 2.8.0 Install Clock 52MHz di Ubuntu 13.04]] '''RECOMMENDED'''
 +
* [[OpenBTS: 2.8 dari SVN Install Clock 52MHz dengan UHD tanpa GNURadio]] ''NOT RECOMMENDED''
 
* [[OpenBTS: 2.8 Edit User di sqlite3.db]] '''RECOMMEND'''
 
* [[OpenBTS: 2.8 Edit User di sqlite3.db]] '''RECOMMEND'''
* [[OpenBTS: Yate Softswitch]]
+
* [[OpenBTS: Yate Softswitch]] '''RECOMMENDED'''
 +
* [[OpenBTS: Yate Softswitch install Ubuntu 12.10]] '''RECOMMENDED'''
 +
* [[OpenBTS: Yate Softswitch install Ubuntu 13.04]] '''RECOMMENDED'''
 
* [[OpenBTS: Yate Config Test]]
 
* [[OpenBTS: Yate Config Test]]
 
* [[OpenBTS: 2.8 Instalasi Real Time Asterisk]] '''RECOMMENDED'''
 
* [[OpenBTS: 2.8 Instalasi Real Time Asterisk]] '''RECOMMENDED'''
 
* [[OpenBTS: 2.8 Menjalankan]] '''RECOMMENDED'''
 
* [[OpenBTS: 2.8 Menjalankan]] '''RECOMMENDED'''
 
* [[OpenBTS: 2.8 Konfigurasi]]
 
* [[OpenBTS: 2.8 Konfigurasi]]
 +
* [[OpenBTS: 2.8 Konfigurasi Cognitive Radio Elsabagh]]
 
* [[OpenBTS: 2.8 Konfigurasi Subscriber Registery]]
 
* [[OpenBTS: 2.8 Konfigurasi Subscriber Registery]]
 
* [[OpenBTS: Database SQLite]]
 
* [[OpenBTS: Database SQLite]]
 +
* [[OpenBTS: Set SQLite Subscriber Registry secara manual]]
 +
* [[OpenBTS: Set SQLite parameter smqueue]]
 +
* [[OpenBTS: FreeSWITCH]]
  
 
===Multi OpenBTS 2.8===
 
===Multi OpenBTS 2.8===
  
* [[OpenBTS: Pola Multi OpenBTS]]
+
* [[OpenBTS: Pola Multi OpenBTS]] '''RECOMMENDED'''
 +
* [[Multi OpenBTS: Catatan Konfigurasi]] '''RECOMMENDED'''
 +
* [[Multi OpenBTS: Catatan BSIC=NCC+BCC]]
 +
* [[Multi OpenBTS: Catatan Frekuensi Planning di GSM]]
 +
* [[Multi OpenBTS: Catatan BTS Color Code BCC di GSM]]
 +
* [[Multi OpenBTS: Catatan Network Color Code NCC di GSM]]
 +
* [[Multi OpenBTS: Catatan BCCH]]
 +
* [[Multi OpenBTS: Catatan Public Land Mobile Network PLMN]]
 +
 
 +
===OpenBTS 3.1.x===
 +
 
 +
* [[OpenBTS: Install UHD untuk USRP1]]
 +
* [[OpenBTS: UHD Identifikasi Device]]
 +
* [[OpenBTS: OpenBTS 3.1.3 Compile]] '''Tidak bisa untuk USRP1'''
 +
* [[OpenBTS: Yate Compile]]
  
 
===Ettus E110===
 
===Ettus E110===
  
 
* [[OpenBTS: E110 Cara Login]]
 
* [[OpenBTS: E110 Cara Login]]
* [[OpenBTS: E110 Install Image di MicroSD]]
+
* [[OpenBTS: E110 Install Image di MicroSD]] '''*RECOMMENDED*'''
 
* [[OpenBTS: E110 Cek Daughter Board]]
 
* [[OpenBTS: E110 Cek Daughter Board]]
 
* [[OpenBTS: E110 Mengubah Master Clock]]
 
* [[OpenBTS: E110 Mengubah Master Clock]]
 
* [[OpenBTS: E110 Kalibrasi Clock]]
 
* [[OpenBTS: E110 Kalibrasi Clock]]
 +
* [[OpenBTS: E110 Konfigurasi Jaringan]]
 
* [[OpenBTS: E110 Bekerja dengan opkg]]
 
* [[OpenBTS: E110 Bekerja dengan opkg]]
 +
* [[OpenBTS: E110 Instalasi iptables]]
 
* [[OpenBTS: E110 GNURadio]]
 
* [[OpenBTS: E110 GNURadio]]
* [[OpenBTS: E110 Install UHD Image]]
+
* [[OpenBTS: E110 Compile UHD]] ''Not Recommended''
 +
* [[OpenBTS: E110 Compile UHD dari Release Bukan git]] ''Not Recommended''
 +
* [[OpenBTS: E110 UHD burn EEPROM RFX Board]] ''Not Recommended''
 +
* [[OpenBTS: E110 Install UHD Image]] ''Not Recommended''
 
* [[OpenBTS: E110 Instalasi OpenBTS]]
 
* [[OpenBTS: E110 Instalasi OpenBTS]]
 
* [[OpenBTS: E110 Instalasi OpenBTS 2.6]] ''NOT RECOMMENDED''
 
* [[OpenBTS: E110 Instalasi OpenBTS 2.6]] ''NOT RECOMMENDED''
 +
* [[OpenBTS: E110 Instalasi OpenBTS 2.8 untuk MultiBTS]] '''*RECOMMENDED*'''
 +
* [[OpenBTS: E110 Yate Softswitch]]
 +
 +
===Ettus N210===
 +
 +
* [[OpenBTS: N210 Instalasi GPSDO Kit]]
 +
* [[OpenBTS: N210 GNURadio]]
 +
* [[OpenBTS: N210 GNURadio 3.7.0]]
 +
* [[OpenBTS: N210 Instalasi OpenBTS]]
 +
* [[OpenBTS: N210 Instalasi Yate]]
 +
* [[OpenBTS: N210 Yate Config Test]]
 +
* [[OpenBTS: N210 Burn Firmware]]
 +
 +
===RangeNetworks===
 +
 +
* [[OpenBTS: RangeNetwork Foto]]
 +
* [[OpenBTS: RangeNetwork menggunakan USB recovery image]]
 +
* [[OpenBTS: RangeNetwork Default Setting]]
 +
* [[OpenBTS: RangeNetwork Instalasi UHD]]
 +
* [[OpenBTS: RangeNetwork Compile GNURadio UHD]]
 +
* [[OpenBTS: RangeNetwork Compile]]
 +
* [[OpenBTS: RangeNetwork Compile OpenBTS 2.8.0]]
 +
* [[OpenBTS: RangeNetwork Compile OpenBTS 3.1.3]]
 +
* [[OpenBTS: RangeNetwork Yate Compile]] '''*RECOMMENDED*'''
 +
* [[OpenBTS: RangeNetwork Web Interface]]
 +
* [[OpenBTS: RangeNetwork Trunk ke Asterisk Lain]]
 +
* [[OpenBTS: RangeNetwork Audit]]
 +
* [[VoIP: Trunk]]
 +
 +
===GPRS===
 +
 +
* [[OpenBTS: GPRS]]
 +
* [[OpenBTS: GPRS Konfigurasi]]
 +
* [[OpenBTS: GPRS untuk dibelakang Router dengan NAT]]
 +
 +
===Briker OpenBTS===
 +
 +
* [[OpenBTS: Briker]]
 +
 +
===FreeSWITCH OpenBTS===
 +
 +
* [[OpenBTS: FreeSWITCH]]
  
 
===Power Amplifier===
 
===Power Amplifier===
Line 292: Line 399:
 
* [[Power Amplifier 900MHz]]
 
* [[Power Amplifier 900MHz]]
 
* [[Duplexer]]
 
* [[Duplexer]]
 +
* [[OpenBTS: Menaikan Jangkauan OpenBTS]]
  
 
===Lain Lain===
 
===Lain Lain===
Line 322: Line 430:
 
* [[OpenBTS: Daftar Workshop atau Seminar yang pernah dilakukan]]
 
* [[OpenBTS: Daftar Workshop atau Seminar yang pernah dilakukan]]
 
* [[OpenBTS: Daftar Artikel di Media]]
 
* [[OpenBTS: Daftar Artikel di Media]]
 +
* [[OpenBTS: Permohonan Kanal dan DID untuk OpenBTS]]
 +
* [[OpenBTS: 2013/02/19 - OpenBTS TelkomSel Mengudara di Muscat Oman]]
 +
* [[OpenBTS: Beroperasi di Papua]]
  
 
===Dokumentasi Video===
 
===Dokumentasi Video===
  
 +
* http://www.metrotvnews.com/read/newsprograms/2012/10/14/14624/212/Teknologi-BTS
 
* http://youtu.be/8ogOcUSpINU (1/6)
 
* http://youtu.be/8ogOcUSpINU (1/6)
 
* http://youtu.be/F5d7HGuhppk (2/6)
 
* http://youtu.be/F5d7HGuhppk (2/6)
Line 331: Line 443:
 
* http://youtu.be/6LCuoeI57ak (5/6)
 
* http://youtu.be/6LCuoeI57ak (5/6)
 
* http://youtu.be/-dEqcHoIlYk (6/6)
 
* http://youtu.be/-dEqcHoIlYk (6/6)
 +
* http://www.youtube.com/watch?v=Ff_rw4kAOZg&feature=share
 +
 +
===Perjuangan OpenBTS===
 +
 +
* http://www.technologyreview.com/news/522371/how-remote-places-can-get-cellular-coverage-by-doing-it-themselves/?utm_campaign=socialsync&utm_medium=social-post&utm_source=twitter
 +
 +
  
 
[[Category: Wireless]]
 
[[Category: Wireless]]
 
[[Category: Selular]]
 
[[Category: Selular]]

Latest revision as of 05:59, 11 March 2014

Backup SD CARD Bawaan dari Ettus

CARA INI RECOMMENDED

Masukan SD card ke PC.

mkdir /e110-backup
cd /e110-backup
dd if=/dev/sdc of=sde110-ori.bin

Untuk mengembalikan

cd /e110-backup
dd if=sde110-ori.bin of=/dev/sdc

Sumber Image untuk E110

Ada beberapa sumber image yang menarik utk Ettus E110

Menggunakan Build Directory

Download

http://files.ettus.com/e1xx_images/current/e1xx-003-make.tar.bz2

Buka

cp e1xx-003-make.tar.bz2 /usr/local/src/
cd /usr/local/src
tar jxvf e1xx-003-make.tar.bz2

Masukan microSD ke laptop / PC. Kalau microSD mount automatis, maka kita peru umount

sudo umount /media/boot-003/
sudo umount /media/rootfs-e1xx-003/

Untuk cek lokasi microSD menggunakan perintah

sudo fdisk -l

Misalnya keluar

   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1   *         128      131071       65472    c  W95 FAT32 (LBA)
/dev/sdb2          131072     8054783     3961856   83  Linux

Maka device kita adalah

/dev/sdb

Jika perlu kita buang semua partisi yang ada menggunakan fdisk

fdisk /dev/sdb
d 1
d 2
q

Gunakan 'MakeEttusSDCard.sh' yang akan mengurus partisi dll.

cd /usr/local/src/e1xx-003
sudo ./MakeEttusSDCard.sh /dev/sdb

Keluaran akan kira-kira

..
..
Populating boot partition files
Boot partition complete
Populating rootfs partition files
This will take several minutes . . .
Rootfs partition complete
SD card creation was successful

Ini akan membutuhkan waktu lumayan lama, jika selesai maka akan melaporkan sukses.

Membuat Image Dari E100-sd-07OCT2011-1.bin.gz

CARA INI TIDAK BERHASIL - ERROR FILE SYSTEM READ ONLY

Lakukan

gunzip E100-sd-07OCT2011-1.bin.gz 
dd if=E100-sd-07OCT2011-1.bin of=/dev/sdb

Tunggu agak lama utk menyelesaikan proses penulisan

Cara Lain Untuk Membuat Image E1xx SD card

Image berikut agak repot untuk digunakan karena tidak ada asterisk, openbts, hanya ada gnuradio saja. Untuk mencobanya silahkan download dari

http://files.ettus.com/e1xx_images/e1xx-003/
http://files.ettus.com/e1xx_images/e1xx-002/
http://files.ettus.com/e1xx_images/

Cek lokasi MicroSD (biasanya /dev/sdb), kalau perlu di umount

fdisk -l
sudo umount /path/to/mount/point/partition

Download file dan lakukan proses pembuatan SD card

sudo su
cp e1xx-002-make.tar.bz2 /usr/local/src/
cd /usr/local/src
tar jxvf e1xx-002-make.tar.bz2
cd /usr/local/src/e1xx-002
./MakeEttusSDCard.sh /dev/sdb

Ini akan membutuhkan beberapa waktu untuk menyelesaikan

Download Image

Tampaknya Image ini lebih baik untuk digunakan untuk development openbts karena sudah banyak yang di siapkan.

wget http://dl.dropbox.com/u/14618236/MLO
wget http://dl.dropbox.com/u/14618236/u-boot.bin-for-3.0.bin
wget http://dl.dropbox.com/u/14618236/uImage-3.0-pm-r0a-usrp-e1xx.bin
wget http://dl.dropbox.com/u/14618236/console-openbts-devel-image-usrp-e1xx.tar.gz

Install Image

CARA INI TIDAK BERHASIL - ERROR FILE SYSTEM READ ONLY

Langkah berikut adalah untuk menginstall image di SD card di Linux. Sangat di sarankan untuk membackup terlebih dulu isi SD card sebelum anda melakukan hal ini.

Masukan SD card ke card reader. Akan terdeteksi dua partisi yaitu FAT dan rootfs. Jika tidak, partisi tersebut perlu di mount secara manual.

fdisk -l
Disk /dev/sdb: 4124 MB, 4124049408 bytes
127 heads, 62 sectors/track, 1022 cylinders, total 8054784 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000

   Device Boot      Start         End      Blocks   Id  System
/dev/sdb1   *         128      131071       65472    c  W95 FAT32 (LBA)
/dev/sdb2          131072     8054783     3961856   83  Linux

Di mount

mkdir /media/FAT
mkdir /media/rootfs
mount /dev/sdb1 /media/FAT
mount /dev/sdb2 /media/rootfs

Jika di perlukan untuk mempartisi ulang maka besar partisi

FAT    FAT32  60Mbyte
rootfs ext3   sisa-nya

Partisi FAT berisi software untuk boot, seperti kernel Linux. Partisi rootfs berisi lainnya, termasuk kernel modul, paket yang terinstalasi dll.

$ ls /media/
FAT  rootfs

Instal MLO. Timpa MLO lama dengan MLO baru. Jika ini tidak betul dilakukan, maka partisi perlu di format. Lakukan,

cd /media/FAT
cp <download location>/MLO MLO
cp <download location>/u-boot.bin-for-3.0.bin u-boot.bin
cp <download location>/uImage-3.0-pm-r0a-usrp-e1xx.bin uImage

Hapus root filesystem. Pastikan bahwa directory yang digunakan benar, jika tidak kita akan kehilangan data.

sudo rm -Rf /media/rootfs/*

Cara lain yang lebih low level memformat partisi tersebut

fdisk -l # cek partisi misalnya /dev/sdb2 atau /dev/sdc2
mkfs.ext3 /dev/sdb2
e2label /dev/sdb2 rootfs
mkdir /media/rootfs
mount /dev/sdb2 /media/rootfs


Install root filesystem yang baru di partisi rootfs yang di mount.

cd /media/rootfs
sudo tar xvfz <download location>/console-openbts-devel-image-usrp-e1xx.tar.gz .

Unmount partisi. Perhatikan umount akan membutuhkan beberapa menit sebelum SD card dapat di cabut dengan aman.

cd /media
umount FAT
umount rootfs

Selesai sudah SD card dapat di lepas dari PC / laptop. Kita masukan ke E110. E110 dapat di boot.

Masukan MicroSD di E110

Tampak pada gambar adalah lokasi tempat MicroSD di E110

Lokasi MicroSD pada E110


Referensi

Pranala Menarik

Persiapan

Script

OpenBTS 2.6

OpenBTS 2.8

Multi OpenBTS 2.8

OpenBTS 3.1.x

Ettus E110

Ettus N210

RangeNetworks

GPRS

Briker OpenBTS

FreeSWITCH OpenBTS

Power Amplifier

Lain Lain

Catatan Legal dan Pendukung

Catatan Sejarah

Dokumentasi Video

Perjuangan OpenBTS