USRP: Menyambungkan ClockTamer ke USRP1

From OnnoWiki
Jump to navigation Jump to search

USRP 2, N2x0, E1x0 and B1x0

This page focuses on connecting ClockTamer to a USRP1. Yet you can use ClockTamer with USRP 2, N2x0, E1x0 and B1x0 as well, we just don't have a detailed manual for this. In general, to use ClockTamer with USRP's other then USRP1 you should connect it to "10MHz external reference" input and configure ClockTamer to output 10MHz frequency. USRP1

Installation of a ClockTamer to USRP1 has three stages:

   USRP1 modification to disable internal USRP1 clock reference and enable external clock input.
   Proper termination of the USRP1 clock input.
   16-pin connector installation on a RFX daughter board (optional).
   R7 current limiting resistor removal (optional).
   ClockTamer installation on a USRP1. 

All these steps are described in more details below.

USRP1 modifications

Re-clocking.jpg

According to Synchronizing multiple USRP1s on USRP wiki, bullet "For the slave boards" you should do following modifications in order to connect external clock to USRP:

   Solder an SMA connector into J2001. This is the clock input. Be careful when soldering the SMA connector so you don't break the delicate trace from J2001 to C927.
   Note that you won't be able to fit a TVRX in the RXB slot anymore once you do this.
   Move R2029 to R2030. This disables the onboard clock. R2029/R2030 is a 0-ohm resistor. This step is not strictly necessary.
   Move C925 to C926.
   Remove C924. 

Terminating clock input with 50 Ohm resistor

We strongly encourage you to install 50 Ohm termination resistor on USRP side no matter whether you use ClockTamer's CMOS or half-LVDS output (read below how to do this). If you use a CMOS output of ClockTamer then everything will likely work without terminating resistor and we're not aware of any damaged USRP due to absence of this terminating resistor, but such usage is out of specs. Don't blame us if you burn your USRP by using ClockTamer without installing the terminating resistor on USRP1. If you plan to use a half-LVDS output of ClockTamer, then terminating resistor is a must to get it working. Using half-LVDS output without a proper terminating resistor at J2001 will result in signal bouncing and USRP1 will not be able to lock to the clock.

Note: You must solder termination resistor to USRP near the clock input connector J2001. If you solder 50 Ohm resistor to ClockTamer instead of USRP, it will not work.

"50 Ohm resistor" is a term often used in RF discussions and usually means resistors with a nominal close to 50 Ohm. Both 49.9 Ohm or 51 Ohm resistors are ok. We use 51 Ohm resistors in our setups usually.

Below are pictures of our way of soldering an terminating resistor to J2001. If you find a better/safer way - please let us know (and send us pictures if possible).

Side.jpg
Top.jpg


RFX900/RFX1800 16-pin connector

If you have new RFX daughter board most likely it don't have J24 16-pin connector soldered. You may want to solder the provided connector to J24 to securely fixate ClockTamer inside of a USRP1. This is not strictly required and ClockTamer will perfectly work without this connector.

J24 connector may also be used to communicate with ClockTamer without a miniUSB cable, but this feature is in beta stage and is not recommended for new users. Fan connector's current limiting resistor

If you want to power your ClockTamer from the USRP1's fan connector, and still be able to power the fan, you have to replace a current limiting resistor R7 with 0 Ohm resistor or a short circuit. This resistor is located right next to the fan power connector J3. Picture below shows the location of the R7 resistor with a short circuit instead of the actual resistor. Soldering on the picture is quite rough, we know you could do better :)


Current-limiting-resistor.jpg


ClockTamer installation Package contents

ClockTamer package should contain the following items:

   Flat ribbon cable. It can be used to connect a ClockTamer to RFX daughter board connector if you place ClockTamer remotely. It will not be used in this manual, because the normal way to place ClockTamer is to place it directly on the RFX board connector (see below).
   ClockTamer itself. If your ClockTamer is GPS enabled, it have a female U.FL pigtail attached to it (not shown on the picture below). Female U.FL pigtail is used to connect ClockTamer to GPS antenna.
   Male U.FL pigtail. Used to connect ClockTamer to USRP1 clock input.
   2-wire power cable.
   16-pin connector to solder to RFX daughter board.
   SMA connector to solder to USRP1 clock input.
   GPS antenna (only if ClockTamer is GPS-enabled, not shown on the picture below). 
1-ClockTamer-kit.jpg


Connecting pigtail

First, connect male U.FL pigtail to the ClockTamer as shown on the pictures below. Only CMOS output #1 is enabled by default, and thus it requires less effort from you to get your setup working. We strongly encourage you to use it. If you want to enable other outputs, you can do this with ClockTamer GUI or manually with ClockTamer control protocol.

Make sure to connect pigtail securely. Loose connection may lead to bad performance or non-responsive USRP1.

Picture of the pigtail connected to output #1 - the default CMOS output.

2-ClockTamer-CMOS.jpg


Picture of the pigtail connected to output #0 - a half-LVDS output. You have to enable this output before using it (see above).

3-ClockTamer-halfLVDS.jpg


Connecting power cord

Now, connect power cord to the ClockTamer. ClockTamer power connectors are connected directly to each other to allow "chained" connection of the second load (another ClockTamer or a fan). Thus you can connect power cord to any of the power connectors, both will work.

4-ClockTamer-with-power.jpg


Connecting to a USRP1 clock input

Then connect ClockTamer to the USRP1 clock input, as shown on the picture below. Make sure to tighten the connector securely.


5-clock-connected.jpg

Placing ClockTamer and power connection

This step is pretty easy. Just place ClockTamer as shown on the picture bellow to fixate it inside of the USRP1 and connect the power cord to the USRP1's fan connector. If you don't have J24 connector, you have to find some other place for your ClockTamer to be fixated. If you do so, make sure to not short-circuit any wires on the ClockTamer or the USRP1.

6-power-connected.jpg


Connecting the USRP1's fan

If you have removed the power limiting resistor from the fan power connector (see above), then you can connect the USRP1's fan to the ClockTamer, as shown on the picture.


7-fan-connected.jpg

Testing

   Power on your USRP1.
   If you ClockTamer is NOT connected to miniUSB, it should NOT have its LED lighting. If your ClockTamer IS connected to miniUSB, its LED SHOULD blink once and then light continuously.
   One of USRP1's LEDs should blink fast.
   Use some application from GnuRadio or UHD to check that you can get data from your USRP1 or send data to it as usual. We prefer to use usrp_fft.py for this purpose. 


Referensi

Pranala Menarik

Persiapan Hardware

OpenBTS 2.6

OpenBTS 2.8

Ettus E110

Lain Lain

Catatan Legal dan Pendukung

Catatan Sejarah