Difference between revisions of "Arduino: Ethernet DHCP Address Printer"

From OnnoWiki
Jump to navigation Jump to search
(New page: Sumber: https://www.arduino.cc/en/Tutorial/DhcpAddressPrinter This sketch uses the DHCP extensions to the Ethernet library to get an IP address via DHCP and print the address obtained u...)
 
 
Line 3: Line 3:
  
  
This sketch uses the DHCP extensions to the Ethernet library to get an IP address via DHCP and print the address obtained using an Arduino Ethernet shield.
+
Sketch ini menggunakan DHCP extensions dari Ethernet library untuk memperoleh IP address via DHCP dan print IP address yang di peroleh menggunakan Arduino Ethernet shield.
  
DHCP is used to assign an IP address when Ethernet.begin(mac) is called. Using DHCP significantly increases the size of a sketch. Using the localIP() function, the assigned IP address is sent out via the serial monitor.
+
DHCP menggunakan IP address yang dialokasikan saat  Ethernet.begin(mac) dipanggil. Menggunakan DHCP akan sangat memperbesar size sketch. Menggunakan  fungsi localIP(), alokasi IP address akan dikirim keluar melalui serial monitor.
  
Hardware Required
+
Hardware yang dibutuhkan
  
* Arduino or Genuino Board
+
* Arduino atau Genuino Board
 
* Arduino Ethernet Shield  
 
* Arduino Ethernet Shield  
  
 
==Circuit==
 
==Circuit==
  
The Ethernet shield allows you to connect a WizNet Ethernet controller to the Arduino or Genuino boards via the SPI bus. It uses pins 10, 11, 12, and 13 for the SPI connection to the WizNet. Later models of the Ethernet shield also have an SD Card on board. Digital pin 4 is used to control the slave select pin on the SD card.
+
Ethernet shield mengijinkan anda untuk tersambung ke WizNet Ethernet controller ke board Arduino atau Genuino via SPI bus. Dia akan menggunakan pin 10, 11, 12, dan 13 untuk sambungan SPI ke WizNet. Model terakhir Ethernet shield memiliki SD Card on board. Digital pin 4 digunakan untuk control slave select di SD card.
  
The shield should be connected to a network with an ethernet cable. You will need to change the network settings in the program to correspond to your network.
+
Shield disambungkan ke jaringan dengan sebuah kabel ethernet. Kita perlu mengubah network setting di program sesuai dengan jaringan yang kita gunakan.
  
image developed using Fritzing. For more circuit examples, see the Fritzing project page
 
  
In the above image, the Arduino or Genuino board would be stacked below the Ethernet shield.
+
==Code==
Code
 
  
 
  /*
 
  /*

Latest revision as of 07:58, 20 November 2015

Sumber: https://www.arduino.cc/en/Tutorial/DhcpAddressPrinter


Sketch ini menggunakan DHCP extensions dari Ethernet library untuk memperoleh IP address via DHCP dan print IP address yang di peroleh menggunakan Arduino Ethernet shield.

DHCP menggunakan IP address yang dialokasikan saat Ethernet.begin(mac) dipanggil. Menggunakan DHCP akan sangat memperbesar size sketch. Menggunakan fungsi localIP(), alokasi IP address akan dikirim keluar melalui serial monitor.

Hardware yang dibutuhkan

  • Arduino atau Genuino Board
  • Arduino Ethernet Shield

Circuit

Ethernet shield mengijinkan anda untuk tersambung ke WizNet Ethernet controller ke board Arduino atau Genuino via SPI bus. Dia akan menggunakan pin 10, 11, 12, dan 13 untuk sambungan SPI ke WizNet. Model terakhir Ethernet shield memiliki SD Card on board. Digital pin 4 digunakan untuk control slave select di SD card.

Shield disambungkan ke jaringan dengan sebuah kabel ethernet. Kita perlu mengubah network setting di program sesuai dengan jaringan yang kita gunakan.


Code

/*
  DHCP-based IP printer 

  This sketch uses the DHCP extensions to the Ethernet library
  to get an IP address via DHCP and print the address obtained.
  using an Arduino Wiznet Ethernet shield. 

  Circuit:
   Ethernet shield attached to pins 10, 11, 12, 13

  created 12 April 2011
  modified 9 Apr 2012
  by Tom Igoe
  modified 02 Sept 2015
  by Arturo Guadalupi

*/

#include <SPI.h>
#include <Ethernet.h>

// Enter a MAC address for your controller below.
// Newer Ethernet shields have a MAC address printed on a sticker on the shield
byte mac[] = {
  0x00, 0xAA, 0xBB, 0xCC, 0xDE, 0x02
};

// Initialize the Ethernet client library
// with the IP address and port of the server
// that you want to connect to (port 80 is default for HTTP):
EthernetClient client;

void setup() {
  // Open serial communications and wait for port to open:
  Serial.begin(9600);
  // this check is only needed on the Leonardo:
  while (!Serial) {
    ; // wait for serial port to connect. Needed for native USB port  only
  } 

  // start the Ethernet connection:
  if (Ethernet.begin(mac) == 0) {
    Serial.println("Failed to configure Ethernet using DHCP");
    // no point in carrying on, so do nothing forevermore:
    for (;;)
      ;
   }
  // print your local IP address:
  printIPAddress();
}

void loop() {

  switch (Ethernet.maintain())
  {
    case 1:
      //renewed fail
      Serial.println("Error: renewed fail");
      break;

    case 2:
      //renewed success
      Serial.println("Renewed success");

      //print your local IP address:
      printIPAddress();
      break;

    case 3:
      //rebind fail
      Serial.println("Error: rebind fail");
      break;

    case 4:
      //rebind success
      Serial.println("Rebind success"); 

      //print your local IP address:
      printIPAddress();
      break;

    default:
      //nothing happened
      break; 

  }
}

void printIPAddress()
{
  Serial.print("My IP address: ");
  for (byte thisByte = 0; thisByte < 4; thisByte++) {
    // print the value of each byte of the IP address:
    Serial.print(Ethernet.localIP()[thisByte], DEC);
    Serial.print(".");
  }

  Serial.println();
}



Referensi