Difference between revisions of "USRP: ClockTamer Flashing"

From OnnoWiki
Jump to navigation Jump to search
Line 155: Line 155:
 
* [[OpenBTS: Tethr untuk Bencana Alam]]
 
* [[OpenBTS: Tethr untuk Bencana Alam]]
 
* [[USRP: Tip Pemesanan]]
 
* [[USRP: Tip Pemesanan]]
 +
 +
===Script===
 +
 +
* [[OpenBTS: Script Membuat GNURadio 3.4.2 di Ubuntu 13.04]]
 +
* [[OpenBTS: Script Membuat OpenBTS dan yate di Ubuntu 13.04]]
 +
 +
 +
===OpenBTS 2.6===
 +
 +
* [[GNURadio]]
 +
* [[GNURadio: Ubuntu Install]]
 +
* [[GNURadio: Menggunakan UHD]]
 +
* [[GNURadio: Ubuntu Install GNURadio 3.4.2]] '''RECOMMENDED'''
 +
* [[GNURadio: Ubuntu Install GNURadio 3.4.2 Clock 52MHz]] '''RECOMMENDED'''
 +
* [[GNURadio: Ubuntu 13.04 Install GNURadio 3.4.2 Clock 52MHz]] ''NOT RECOMMENDED''
 +
* [[GNURadio: Contoh Aplikasi]]
 +
* [[GNURadio: Spectrum Analizer GSM]]
 +
* [[GNURadio: Mengubah board RFX1800 menjadi RFX900]]
 +
* [[GNURadio: Programming Untuk Pemula]]
 +
* [[OpenBTS: Ubuntu Install]] '''RECOMMENDED'''
 +
* [[OpenBTS: Ubuntu Install OpenBTS 2.6 Clock 52MHz]] '''RECOMMENDED'''
 +
* [[OpenBTS: Ubuntu 13.04 Install OpenBTS 2.6 Clock 52MHz]] ''NOT RECOMMENDED''
 +
* [[OpenBTS: Konfigurasi]] '''RECOMMENDED'''
 +
* [[OpenBTS: Kalibrasi]]
 +
* [[OpenBTS: Konfigurasi Asterisk untuk OpenBTS]] '''RECOMMENDED'''
 +
* [[OpenBTS: Menjalankan smqueue]]
 +
* [[OpenBTS: Mengoperasikan BTS]] '''RECOMMENDED'''
 +
* [[OpenBTS: Tampilan di Nokia saat pakai OpenBTS]]
 +
* [[OpenBTS: Operasi 1800 MHz]]
 +
* [[OpenBTS: Beberapa Tips]]
 +
* [[OpenBTS: USRP2]]
 +
* [[OpenBTS: Amplifier]]
 +
* [[OpenBTS: SMS]]
 +
* [[AirProbe]]
 +
 +
===OpenBTS 2.8===
 +
 +
* [[GNURadio: Ubuntu 11.10 Install]] ''NOT RECOMMENED''
 +
* [[GNURadio: Ubuntu 11.10 instalasi menggunakan Repo]] ''NOT RECOMMENDED''
 +
* [[GNURadio: Download GNURadio]]
 +
* [[GNURadio: Install UHD]]
 +
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.3.0]]
 +
* [[GNURadio: Ubuntu 12.10 Instal GNURadio 3.3.0]]
 +
* [[GNURadio: Ubuntu 12.10 Instal GNURadio 3.4.1]] ''NOT RECOMMENDED''
 +
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.4.2]] '''RECOMMENDED'''
 +
* [[GNURadio: Ubuntu 12.04 Instal GNURadio 3.4.2]] '''RECOMMENDED'''
 +
* [[GNURadio: Ubuntu 12.04.1 Instal GNURadio 3.4.2]] '''RECOMMENDED'''
 +
* [[GNURadio: Ubuntu 12.10 Instal GNURadio 3.4.2]] ''NOT RECOMMENDED''
 +
* [[GNURadio: Ubuntu 13.04 Instal GNURadio 3.4.2]] '''RECOMMENDED'''
 +
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.5.0]] ''NOT RECOMMENDED''
 +
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.5.3.2]] ''NOT RECOMMENDED''
 +
* [[GNURadio: Ubuntu 11.10 Instal GNURadio 3.6.0]] ''NOT RECOMMENDED''
 +
* [[GNURadio: Ubuntu 11.10 Install dari GIT GNURadio]] ''NOT RECOMMENDED''
 +
* [[GNURadio: Ubuntu 11.10 cek USRP Daughter Board]]
 +
* [[GNURadio: UHD]] ''NOT RECOMMENDED''
 +
* [[GNURadio: UHD Image]] ''NOT RECOMMENDED''
 +
* [[GNURadio: UHD burn EEPROM RFX Board di USRP1]] ''NOT RECOMMENDED''
 +
* [[GNURadio: UHD Identifikasi Device]]
 +
* [[OpenBTS: Ubuntu 11.10 Install]]
 +
* [[OpenBTS: dari GIT ttsou]]
 +
* [[OpenBTS: 2.8 dari SVN Install]]
 +
* [[OpenBTS: 2.8 dari SVN Install Clock 52MHz]] '''RECOMMENDED'''
 +
* [[OpenBTS: 2.8 dari SVN Install Clock 52MHz di Ubuntu 12.10]] '''RECOMMENDED'''
 +
* [[OpenBTS: 2.8 dari SVN Install Clock 52MHz di Ubuntu 13.04]] '''RECOMMENDED'''
 +
* [[OpenBTS: 2.8 dari SVN Install Clock 52MHz dengan UHD tanpa GNURadio]] ''NOT RECOMMENDED''
 +
* [[OpenBTS: 2.8 Edit User di sqlite3.db]] '''RECOMMEND'''
 +
* [[OpenBTS: Yate Softswitch]] '''RECOMMENDED'''
 +
* [[OpenBTS: Yate Softswitch install Ubuntu 12.10]] '''RECOMMENDED'''
 +
* [[OpenBTS: Yate Softswitch install Ubuntu 13.04]] '''RECOMMENDED'''
 +
* [[OpenBTS: Yate Config Test]]
 +
* [[OpenBTS: 2.8 Instalasi Real Time Asterisk]] '''RECOMMENDED'''
 +
* [[OpenBTS: 2.8 Menjalankan]] '''RECOMMENDED'''
 +
* [[OpenBTS: 2.8 Konfigurasi]]
 +
* [[OpenBTS: 2.8 Konfigurasi Cognitive Radio Elsabagh]]
 +
* [[OpenBTS: 2.8 Konfigurasi Subscriber Registery]]
 +
* [[OpenBTS: Database SQLite]]
 +
* [[OpenBTS: Set SQLite Subscriber Registry secara manual]]
 +
* [[OpenBTS: FreeSWITCH]]
 +
 +
===Multi OpenBTS 2.8===
 +
 +
* [[OpenBTS: Pola Multi OpenBTS]] '''RECOMMENDED'''
 +
* [[Multi OpenBTS: Catatan Konfigurasi]] '''RECOMMENDED'''
 +
 +
===Ettus E110===
 +
 +
* [[OpenBTS: E110 Cara Login]]
 +
* [[OpenBTS: E110 Install Image di MicroSD]] '''*RECOMMENDED*'''
 +
* [[OpenBTS: E110 Cek Daughter Board]]
 +
* [[OpenBTS: E110 Mengubah Master Clock]]
 +
* [[OpenBTS: E110 Kalibrasi Clock]]
 +
* [[OpenBTS: E110 Konfigurasi Jaringan]]
 +
* [[OpenBTS: E110 Bekerja dengan opkg]]
 +
* [[OpenBTS: E110 Instalasi iptables]]
 +
* [[OpenBTS: E110 GNURadio]]
 +
* [[OpenBTS: E110 Compile UHD]] ''Not Recommended''
 +
* [[OpenBTS: E110 Compile UHD dari Release Bukan git]] ''Not Recommended''
 +
* [[OpenBTS: E110 UHD burn EEPROM RFX Board]] ''Not Recommended''
 +
* [[OpenBTS: E110 Install UHD Image]] ''Not Recommended''
 +
* [[OpenBTS: E110 Instalasi OpenBTS]]
 +
* [[OpenBTS: E110 Instalasi OpenBTS 2.6]] ''NOT RECOMMENDED''
 +
* [[OpenBTS: E110 Instalasi OpenBTS 2.8 untuk MultiBTS]] '''*RECOMMENDED*'''
 +
* [[OpenBTS: E110 Yate Softswitch]]
 +
 +
===Ettus N210===
 +
 +
* [[OpenBTS: N210 Instalasi GPSDO Kit]]
 +
* [[OpenBTS: N210 GNURadio]]
 +
* [[OpenBTS: N210 GNURadio 3.7.0]]
 +
* [[OpenBTS: N210 Instalasi OpenBTS]]
 +
* [[OpenBTS: N210 Instalasi Yate]]
 +
* [[OpenBTS: N210 Yate Config Test]]
 +
* [[OpenBTS: N210 Burn Firmware]]
 +
 +
===RangeNetworks===
 +
 +
* [[OpenBTS: RangeNetwork Default Setting]]
 +
 +
===GPRS===
 +
 +
* [[OpenBTS: GPRS]]
 +
* [[OpenBTS: GPRS Konfigurasi]]
 +
* [[OpenBTS: GPRS untuk dibelakang Router dengan NAT]]
 +
 +
===Briker OpenBTS===
 +
 +
* [[OpenBTS: Briker]]
 +
 +
===FreeSWITCH OpenBTS===
 +
 +
* [[OpenBTS: FreeSWITCH]]
 +
 +
===Power Amplifier===
 +
 +
* [[Driver 900MHz]]
 +
* [[Power Amplifier 900MHz]]
 +
* [[Duplexer]]
 +
* [[OpenBTS: Menaikan Jangkauan OpenBTS]]
 +
 +
===Lain Lain===
 +
 +
* [[OpenBTS: Materi Magang di ICTWATCH]]
 +
* [[OpenBTS: Seminar Outline]]
 +
* [[OpenBTS: Workshop Outline]]
 +
* [[Membuat Base Station GSM Open Source]]
 +
* [[Teknologi Selular]]
 +
* [[GSM: Daftar Channel Frekuensi]]
 +
* [[Wireless Internet]]
 +
* [[OpenBSC]]
 +
* [[AirProbe]]
 +
* [[Base station subsystem]]
 +
* [[GSM]]
 +
* [[Asterisk]]
 +
* [[Mobile phone]]
 +
 +
===Catatan Legal dan Pendukung===
 +
 +
* [[Siapa Bilang OpenBTS Ilegal?]]
 +
* [[OpenBTS: Catatan MNC dan MCC Indonesia]]
 +
* [[OpenBTS: Catatan MNC dan MCC COOL]]
 +
* [[OpenBTS : Alokasi Frekuensi Operator GSM Indonesia]]
 +
* [[GSM: Daftar Channel Frekuensi]]
 +
 +
===Catatan Sejarah===
 +
 +
* [[2011/04/30 - Workshop OpenBTS Pertama di Indonesia dilakukan di Univ Gajah Putih Takengon Aceh Tengah]]
 +
* [[OpenBTS: Daftar Workshop atau Seminar yang pernah dilakukan]]
 +
* [[OpenBTS: Daftar Artikel di Media]]
 +
* [[OpenBTS: Permohonan Kanal dan DID untuk OpenBTS]]
 +
* [[OpenBTS: 2013/02/19 - OpenBTS TelkomSel Mengudara di Muscat Oman]]
 +
* [[OpenBTS: Beroperasi di Papua]]
 +
 +
===Dokumentasi Video===
 +
 +
* http://www.metrotvnews.com/read/newsprograms/2012/10/14/14624/212/Teknologi-BTS
 +
* http://youtu.be/8ogOcUSpINU (1/6)
 +
* http://youtu.be/F5d7HGuhppk (2/6)
 +
* http://youtu.be/90Jgq6bOgrQ (3/6)
 +
* http://youtu.be/cNkx_qNqdfc (4/6)
 +
* http://youtu.be/6LCuoeI57ak (5/6)
 +
* http://youtu.be/-dEqcHoIlYk (6/6)
 +
* http://www.youtube.com/watch?v=Ff_rw4kAOZg&feature=share
 +
 +
===Perjuangan OpenBTS===
 +
 +
* http://www.technologyreview.com/news/522371/how-remote-places-can-get-cellular-coverage-by-doing-it-themselves/?utm_campaign=socialsync&utm_medium=social-post&utm_source=twitter
 +
 +
 +
 +
[[Category: Wireless]]
 +
[[Category: Selular]]
 +
 
==Pranala Menarik==
 
==Pranala Menarik==
  

Revision as of 18:37, 5 January 2014

Environment setup

Our main development platform is Ubuntu and to date it's the only tested build environment. We welcome any additions and corrections to this howto, especially build instructions for other platforms. 

# Install tools required for building firmware.
sudo aptitude install gcc-avr avr-libc unzip

Instructions for installing software for flashing are included into respective sections about flashing, because they depend on the tools you use. Source code preparation

To check out source code and prepare it for building, run following commands in a directory of your choice: 

# Check out clock-tamer project
hg clone https://clock-tamer.googlecode.com/hg/ clock-tamer
cd clock-tamer/board

# Download LUFA 091122, unpack to clock-tamer/LUFA directory and patch it
wget http://www.fourwalledcubicle.com/files/MyUSB/LUFA%20091122.zip
unzip "LUFA 091122.zip"
ln -s "LUFA 091122" LUFA-CUR
patch -p0 <patches/lufa.diff

User code image (for USB flashing)

This image only has usercode without USB bootloader. It can be flash with usual mini-USB cable without any expensive ISP programmer needed.

Building

Depending on the ClockTamer modification you have to define one of the following defines: 

Define                            HWI
------                            ---
TAMER_1515_20                     LMX=1515 LMK=1010 OSC=20
TAMER_2080_20                     LMX=2080 LMK=1010 OSC=20
TAMER_2080_10                     LMX=2080 LMK=1010 OSC=10
TAMER_2080_VCTXCO_26_GPS          LMX=2080 LMK=1010 OSC=26 VCTXCO GPS
TAMER_1650_26_GPS                 LMX=1650 LMK=1010 OSC=26 GPS

You can lookup your hardware info by executing HWI command.

To build flash image for ClockTamer define the variable and run make in clock-tamer/board directory. For the "LMX=2080 LMK=1010 OSC=20" device it is 

CFLAGS="-DTAMER_2080_20" make

If everything went fine, you should get a lot of output, ending with this: 

Size after:
AVR Memory Usage
----------------
Device: at90usb162

Program:    6808 bytes (41.6% Full)
(.text + .data + .bootloader)

Data:        152 bytes (29.7% Full)
(.data + .bss + .noinit)

EEPROM:      411 bytes (80.3% Full)
(.eeprom)

-------- end --------

Flashing

After a successful build in the clock-tamer directory you will find generated Tamer-sdk-v1.hex and Tamer-sdk-v1.eep files, which is ready to be flashed into your ClockTamer. You can also use Tamer-sdk-v1.elf if your programmer supports this.

Actual flashing instructions depend on a type of flasher application you have. We use dfu-programmer, which is readily available in Ubuntu. If you use Ubuntu 9.10 or later, just install it from repository: 

sudo aptitude install dfu-programmer

And if you use Ubuntu 9.04 or your dfu-programmer version is <0.5 we advice you to install it from sources.

Now, when you have dfu-programmer ready, follow this steps:

  • Power off ClockTamer - disconnect power cord AND mini-USB cable.
  • Short-circuit nSS pin of GND (full connector pinout is available here).
  • Connect ClockTamer to a computer with mini-USB cable. LED should light up immediately (WITHOUT flashing once first).
  • Remove short-circuit from nSS to GND.
  • In "board" directory run
make dfu
  • If you want to flash EEPROM data too, run
   make dfu-ee

Full image (for ISP flashing)

This image contains full code, including USB bootloader, and is suitable for ISP flashing.

Note, that to be able to flash ClockTamer over USB after you flash full image, you need to generate your own SDK header. Differences in compiler versions will likely cause different placement of bootloader functions and make standard SDK header useless. Building

The building procedure is similar to those of the standard image, but you should set environment variable "SDK=0", e.g. 

SDK=0 CFLAGS="-DTAMER_2080_20" make

If everything went fine, you'll get something like this: 

Size after:
AVR Memory Usage
----------------
Device: at90usb162

Program:   10618 bytes (64.8% Full)
(.text + .data + .bootloader)

Data:        152 bytes (29.7% Full)
(.data + .bss + .noinit)

EEPROM:      437 bytes (85.4% Full)
(.eeprom)

-------- end --------

Flashing

After a successful build in the clock-tamer directory you will find generated Tamer.hex and Tamer.eep files, which is ready to be flashed into your ClockTamer. You can also use Tamer.elf if your programmer supports this.

Actual flashing instructions depend on a type of flasher and application you have. To flash full image we usually use AVR Dragon. If you have AVR Dragon too, follow this steps:

  • Download "avrdude" from svn and build it. Prebuilt avrdude 5.2 crashes when you try to use it with AVR Dragon, because of this bug. This bug is fixed in rev887 and rev895 in avrdude svn, so make sure you use one of newer revisions.
  • Connect ClockTamer to AVR Dragon, according to SPI pinout.
  • In "board" directory run
   SDK=0 make program
  • If you connected everything correctly, you should have new image uploaded to ClockTamer now.

Note, that this operation erases EEPROM and thus you loose your calibration. If may want to write down your calibrated values somewhere or disable EEPROM write by commenting out this line in makefile: 

AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep


Referensi

  • code.google.com/p/clock-tamer/wiki/LinuxBuildHowto


Pranala Menarik

Persiapan

Script


OpenBTS 2.6

OpenBTS 2.8

Multi OpenBTS 2.8

Ettus E110

Ettus N210

RangeNetworks

GPRS

Briker OpenBTS

FreeSWITCH OpenBTS

Power Amplifier

Lain Lain

Catatan Legal dan Pendukung

Catatan Sejarah

Dokumentasi Video

Perjuangan OpenBTS

Pranala Menarik

Persiapan

Script


OpenBTS 2.6

OpenBTS 2.8

Multi OpenBTS 2.8

Ettus E110

Ettus N210

GPRS

Briker OpenBTS

FreeSWITCH OpenBTS

Power Amplifier

Lain Lain

Catatan Legal dan Pendukung

Catatan Sejarah

Dokumentasi Video

Script


OpenBTS 2.6

OpenBTS 2.8

Multi OpenBTS 2.8

Ettus E110

Ettus N210

RangeNetworks

GPRS

Briker OpenBTS

FreeSWITCH OpenBTS

Power Amplifier

Lain Lain

Catatan Legal dan Pendukung

Catatan Sejarah

Dokumentasi Video

Perjuangan OpenBTS

Retrieved from "https://onnocenter.or.id/wiki/index.php?title=USRP:_ClockTamer_Flashing&oldid=39218"