Difference between revisions of "TCP/IP: Quagga Bagaimana cara menggunakan"

From OnnoWiki
Jump to navigation Jump to search
 
(11 intermediate revisions by the same user not shown)
Line 12: Line 12:
 
Contoh di bawah, zebra dan IPv4 OSPF di aktifkan
 
Contoh di bawah, zebra dan IPv4 OSPF di aktifkan
  
−
  # vi /etc/quagga/daemons
+
  vi /etc/quagga/daemons
  
 
  zebra=yes
 
  zebra=yes
Line 20: Line 20:
 
  ripd=no
 
  ripd=no
 
  ripngd=no  
 
  ripngd=no  
 +
isisd=no
 +
babeld=no
  
 
Restart layanan Quagga:
 
Restart layanan Quagga:
Line 25: Line 27:
 
  # /etc/init.d/quagga restart
 
  # /etc/init.d/quagga restart
  
−
  Stopping Quagga monitor daemon: (watchquagga).
+
  Stopping Quagga monitor daemon: (waiting) .. watchquagga.
 
  Stopping Quagga daemons (prio:0): (ospfd) (zebra) (bgpd) (ripd) (ripngd) (ospf6d) (isisd) (babeld).
 
  Stopping Quagga daemons (prio:0): (ospfd) (zebra) (bgpd) (ripd) (ripngd) (ospf6d) (isisd) (babeld).
 
  Removing all routes made by zebra.
 
  Removing all routes made by zebra.
Line 34: Line 36:
 
Kita dapat mencek status daemon Quagga menggunakan perintah:
 
Kita dapat mencek status daemon Quagga menggunakan perintah:
  
−
  # ps -ef | grep quagga
+
  sudo su
 +
ps -ef | grep quagga
 +
 
 +
quagga    4407    1  0 14:32 ?        00:00:00 /usr/lib/quagga/zebra --daemon -A 192.168.1.255 -A 224.0.0.9
 +
quagga    4411    1  0 14:32 ?        00:00:00 /usr/lib/quagga/ospfd --daemon -A 192.168.1.255 -A 224.0.0.9
 +
root      4415    1  0 14:32 ?        00:00:00 /usr/lib/quagga/watchquagga --daemon zebra ospfd
  
−
UID PID PPID C STIME TTY TIME CMD
 
−
quagga 4632 1 0 22:25 ? 00:00:00 /usr/lib/quagga/ospfd --daemon
 
−
quagga 4636 1 0 22:25 ? 00:00:00 /usr/lib/quagga/zebra --daemon
 
  
 
Jika Quagga daemon tidak stop secara benar, kita dapat meng-kill secara manual dan men-start layanan Quagga:
 
Jika Quagga daemon tidak stop secara benar, kita dapat meng-kill secara manual dan men-start layanan Quagga:
  
−
  # kill -9 "UID number"
+
  sudo su
−
  # /etc/init.d/quagga start
+
kill -9 "UID number"
−
 
+
  /etc/init.d/quagga start
  
 
==File Konfigurasi (file /etc/quagga/*.conf)==
 
==File Konfigurasi (file /etc/quagga/*.conf)==
Line 73: Line 77:
 
  cp /usr/share/doc/quagga/examples/babeld.conf.sample /etc/quagga/babeld.conf
 
  cp /usr/share/doc/quagga/examples/babeld.conf.sample /etc/quagga/babeld.conf
  
−
Another way to do it is to create two empty files called /etc/quagga/ospfd.conf and /etc/quagga/zebra.conf. But in this case you cannot telnet a daemon, you need to configure the telnet permissions with vtsh (see below).
+
Sebetulnya kita dapat saja membuat file .conf kosong.  
 +
Jika ini dilakukan, maka kita tidak dapat telnet ke daemon,
 +
kita perlu mengkonfigurasi ijin telnet dengan vtsh.
  
−
Finally, give user and group ownership to respectively quagga and quaggavty to the files inside the /etc/quagga directory:
+
Selanjutnya, kita perlu memperbaiki user dan group agar sesuai dengan quagga dan quaggavty  
 +
kepada file yang ada di dalam folder /etc/quagga:
  
−
  #chown quagga.quaggavty /etc/quagga/*.conf
+
  chown quagga.quaggavty /etc/quagga/*.conf
−
  #chmod 640 /etc/quagga/*.conf
+
  chmod 640 /etc/quagga/*.conf
  
−
Restart the Quagga service:
+
Restart layanan Quagga :
  
−
  #/etc/init.d/quagga restart
+
  # /etc/init.d/quagga restart
−
 
 
−
Top of the page
 
  
  
−
3. DEBIAN.CONF FILE
+
==DEBIAN.CONF FILE==
  
−
By default, the Quagga daemons are listening only to the loopback interface 127.0.0.1. It means that you can telnet a daemon only on its loopback address 127.0.0.1 and thus cannot access it remotely.
+
Default dari Quagga daemon akan mendengarkan interface loopback di 127.0.0.1. Artinya kita hanya bisa telnet di address 127.0.0.1 dan tidak bisa di akses secara remore.
  
−
If you want to telnet a Quagga daemon remotely you can, in the /etc/quagga/debian.conf file. Either indicate one or several IP addresses or remove the -A option meaning that you can telnet a daemon on any of its IP addresses.
+
Jika kita ingin telnet ke Quagga daemon dari remote, kita dapat mengedit file /etc/quagga/debian.conf.  
 +
Kita dapat memasukan IP address yang di di telnet atau membuang semua opsi -A.
  
−
Here are two examples:
+
Contoh:
  
−
The ospfd daemon is listening to the 127.0.0.1 and 192.168.1.104 IP addresses.
+
* daemon ospfd mendengarkan pada IP address 127.0.0.1 dan 192.168.1.104.
  
 
  ospfd_options=" --daemon -A 127.0.0.1 192.168.1.104"
 
  ospfd_options=" --daemon -A 127.0.0.1 192.168.1.104"
  
−
The zebra daemon is listening to all the Linux interfaces IP addresses. We recommend using this setting. If you want to filter who can access to your router, configure access lists on the router software.
+
* daemon zebra mendengarkan semua IP address di interface Linux. Lebih di rekomendasikan untuk memfilter siapa yang dapat mengakses router.
  
 
  zebra_options=" --daemon "
 
  zebra_options=" --daemon "
  
−
Here is the recommended debian.conf file:
+
Berikut adalah rekomendasi file debian.conf:
  
 
  #vim /etc/quagga/debian.conf
 
  #vim /etc/quagga/debian.conf
Line 112: Line 118:
 
  #
 
  #
 
  vtysh_enable=yes
 
  vtysh_enable=yes
−
  zebra_options=" --daemon -A "
+
  zebra_options=" --daemon -A 127.0.01"
−
  bgpd_options=" --daemon -A "
+
  bgpd_options=" --daemon -A 127.0.01"
−
  ospfd_options=" --daemon -A "
+
  ospfd_options=" --daemon -A 127.0.01"
−
  ospf6d_options="--daemon -A "
+
  ospf6d_options="--daemon -A ::1"
−
  ripd_options=" --daemon -A "
+
  ripd_options=" --daemon -A 127.0.01"
−
  ripngd_options="--daemon -A "
+
  ripngd_options="--daemon -A ::1"
−
  isisd_options=" --daemon -A "
+
  isisd_options=" --daemon -A 127.0.01"
 +
babeld_options=" --daemon -A 127.0.01"
  
−
The "vtysh_enable=yes" setting is required to access the Quaggga router via vtysh. (see vtysh section).
+
Konfigurasi "vtysh_enable=yes" dibutuhkan untuk mengakses router Quagga menggunakan vtysh.
  
−
Restart the Quagga service
+
Restart layanan Quagga
  
 
  #/etc/init.d/quagga restart
 
  #/etc/init.d/quagga restart
  
−
Top of the page
+
==VTYSH==
 +
 
 +
Kita bisa mengakses daemon di Quagga dengan cara telnet ke port masing-masing daemon. Port tersebut adalah:
  
  
−
4. VTYSH
+
zebra          2601/tcp                        # zebra vty
 +
ripd            2602/tcp                        # ripd vty (zebra)
 +
ripngd          2603/tcp                        # ripngd vty (zebra)
 +
ospfd          2604/tcp                        # ospfd vty (zebra)
 +
bgpd            2605/tcp                        # bgpd vty (zebra)
 +
ospf6d          2606/tcp                        # ospf6d vty (zebra)
 +
ospfapi        2607/tcp                        # OSPF-API
 +
isisd          2608/tcp                        # ISISd vty (zebra)
  
−
As indicated in the Quagga introduction, you can access the daemons by telnetting their port number because each daemon has its own configuration file and terminal interface.
 
  
−
zebra:              2601
+
Sebagai contoh, untuk akses ke daemon ospfd:
−
ripd:                2602
 
−
ripng:              2603
 
−
ospfd:               2604
 
−
bgpd:                2605
 
−
ospf6d:              2606
 
  
−
By instance, to access the ospfd daemon:
+
telnet localhost 2604
  
−
#telnet localhost 2604
+
atau
  
−
As it's not very practical to configure your router by telnetting its daemons separately, vtysh has been created to configure everything in one single interface.
+
telnet localhost ospfd
  
−
To use vtysh, you must first create its configuration file as follows:
+
Akan sangat tidak praktis untuk mengkonfigurasi router dengan cara telnet ke masing-masing daemon secara terpisah,
 +
oleh karenanya dibuatlah vtysh untuk mengkonfigurasi segala sesuatu di satu interface.
  
−
  #cp /usr/share/doc/quagga/examples/vtysh.conf.sample /etc/quagga/vtysh.conf
+
Untuk mmenggunakan vtysh, kita pertama-tama perlu membuat file konfigurasi sebagai berikut:
 +
 
 +
  cp /usr/share/doc/quagga/examples/vtysh.conf.sample /etc/quagga/vtysh.conf
 +
 
 +
Isinya /etc/quagga/vtysh.conf
  
−
/etc/quagga/vtysh.conf
 
 
  !
 
  !
 
  ! Sample
 
  ! Sample
Line 159: Line 173:
 
  !
 
  !
  
−
Apply correct permissions and restart Quagga:
+
Betulkan ijin dan restart Quagga:
  
−
  #chown quagga.quaggavty /etc/quagga/*.conf
+
  chown quagga.quaggavty /etc/quagga/*.conf
−
  #chmod 640 /etc/quagga/*.conf
+
  chmod 640 /etc/quagga/*.conf
−
  #/etc/init.d/quagga restart
+
  /etc/init.d/quagga restart
  
 
In the example above the "service integrated-vtysh-config" setting has been disabled (recommended). In this case, when you save the config under vtysh, it will be stored in separate files depending on the protocols you activated.
 
In the example above the "service integrated-vtysh-config" setting has been disabled (recommended). In this case, when you save the config under vtysh, it will be stored in separate files depending on the protocols you activated.
Line 186: Line 200:
 
Then it's useful to add the "VTYSH_PAGER=more" setting in your /etc/environment file, otherwise you will see an unfriendly "(END)" blinking in the left-down corner of the screen each time your enter a command and will need to press the "q" key to continue.
 
Then it's useful to add the "VTYSH_PAGER=more" setting in your /etc/environment file, otherwise you will see an unfriendly "(END)" blinking in the left-down corner of the screen each time your enter a command and will need to press the "q" key to continue.
  
−
#echo VTYSH_PAGER=more > /etc/environment
+
#echo VTYSH_PAGER=more > /etc/environment
 +
 
 
Log off and log on to enable the environment setting. You can now access the Quagga router with the vtysh command:
 
Log off and log on to enable the environment setting. You can now access the Quagga router with the vtysh command:
  
−
#vtysh
+
# vtysh
−
Hello, this is Quagga (version 0.99.6).
 
−
Copyright 1996-2005 Kunihiro Ishiguro, et al.
 
  
−
  quagga-router#
+
  Hello, this is Quagga (version 0.99.22).
 +
Copyright 1996-2005 Kunihiro Ishiguro, et al.
 +
 +
ubuntu#  
  
−
If you want to run a Quagga command from the Linux shell:
+
Jika kita ingin menjalankan perintah Quagga dari Shell Linux, lakukan:
  
−
#vtysh -c "command"
+
vtysh -c "command"
−
For instance, vtysh -c "show ip route" will display the Quagga routing table.
+
 
 +
Contoh:
 +
 
 +
vtysh -c "show ip route"
 +
 
 +
akan menampilkan tabel routing.
  
 
You can use Ping and traceroute to perform connectivity checks from the vtysh prompt. Of course, these two programs need to be installed on the Linux machine. Ping is generally installed by default but traceroute often not.
 
You can use Ping and traceroute to perform connectivity checks from the vtysh prompt. Of course, these two programs need to be installed on the Linux machine. Ping is generally installed by default but traceroute often not.
 
To install traceroute:
 
To install traceroute:
  
−
#apt-get install traceroute
+
#apt-get install traceroute
−
Top of the page
 
  
 +
==IP FORWARDING==
  
−
5. IP FORWARDING:
+
IP forwarding dibutuhkan untuk mentransfer paket antar interface di sebuah sistem Linux.
  
−
IP forwarding is required to transfer packets between the network interfaces of a Linux system.
+
echo "1" > /proc/sys/net/ipv4/ip_forward
−
See a picture of the Linux kernel routing.
 
  
−
#echo "1" > /proc/sys/net/ipv4/ip_forward
+
Perintah di atas akan menambahkan nilai "1" dalam file /proc/sys/net/ipv4/ip_forward dan mengaktifkan IP forwarding.
 +
jika kita menginginkan agar IP forwarding tetap ada saat Linux reboot, lakukan
  
−
The command above will add the "1" value inside the /proc/sys/net/ipv4/ip_forward file and thus activate the IP forwarding.
+
echo "net.ipv4.ip_forward = 1" >> /etc/sysctl.conf
−
If you want to keep the IP forwarding after a Linux reboot:
 
  
−
#echo "net.ipv4.ip_forward = 1" >> /etc/sysctl.conf
+
Jika juga dapat mencek status ip_forwarding di router Quagga,
 +
menggunakan perintah:
  
−
It is possible to check the ip_forwarding status under the Quagga router:
+
show ip forwarding
  
−
#show ip forwarding
+
Akan keluar
  
−
IP forwarding is on
+
IP forwarding is on
  
−
In this case the IP forwarding is activated.
+
Jika IP forwarding di aktifkan.
  
−
Top of the page.
+
==SPEED/DUPLEX==
−
 
 
−
 
 
−
6. SPEED/DUPLEX:
 
  
 
It is not possible to set the duplex and speed settings on the Quagga plateform. You have to configure them at the Linux level.
 
It is not possible to set the duplex and speed settings on the Quagga plateform. You have to configure them at the Linux level.
 
Use the interface configuration tutorial for assistance.
 
Use the interface configuration tutorial for assistance.
−
 
−
Top of the page.
 
−
 
−
 
  
 
==Pranala Menarik==
 
==Pranala Menarik==

Latest revision as of 11:04, 13 November 2013

Daemon di Quagga

Kita harus mengaktifkan daemon di quagga sesuai dengan routing protokol yang kita inginkan di router kita. 

zebra:    Interface declaration and static routing
bgpd:     BGP routing protocol
ospfd:    OSPF routing protocol
ospf6d:   OSPF IPv6 routing protocol
ripd:     RIP v2 routing protocol
ripngd:   RIP Ipv6 routing protocol

Contoh di bawah, zebra dan IPv4 OSPF di aktifkan 

vi /etc/quagga/daemons

zebra=yes
bgpd=no
ospfd=yes
ospf6d=no
ripd=no
ripngd=no 
isisd=no
babeld=no

Restart layanan Quagga: 

# /etc/init.d/quagga restart

Stopping Quagga monitor daemon: (waiting) .. watchquagga.
Stopping Quagga daemons (prio:0): (ospfd) (zebra) (bgpd) (ripd) (ripngd) (ospf6d) (isisd) (babeld).
Removing all routes made by zebra.
Loading capability module if not yet done.
Starting Quagga daemons (prio:10): zebra ospfd.
Starting Quagga monitor daemon: watchquagga.

Kita dapat mencek status daemon Quagga menggunakan perintah: 

sudo su
ps -ef | grep quagga

quagga    4407     1  0 14:32 ?        00:00:00 /usr/lib/quagga/zebra --daemon -A 192.168.1.255 -A 224.0.0.9
quagga    4411     1  0 14:32 ?        00:00:00 /usr/lib/quagga/ospfd --daemon -A 192.168.1.255 -A 224.0.0.9
root      4415     1  0 14:32 ?        00:00:00 /usr/lib/quagga/watchquagga --daemon zebra ospfd


Jika Quagga daemon tidak stop secara benar, kita dapat meng-kill secara manual dan men-start layanan Quagga: 

sudo su
kill -9 "UID number"
/etc/init.d/quagga start

File Konfigurasi (file /etc/quagga/*.conf)

Kita harus membuat file konfigurasi (walaupun itu kosong) setiap kali kita akan mengaktifkan daemon Quagga. Setiap daemon akan membaca file tertentu: 

vtysh:     vtysh.conf
zebra:     zebra.conf
bgpd:      bgpd.conf
ospfd:     ospfd.conf
ospf6d:    ospf6d.conf
ripd:      ripd.conf
ripngd:    ripngd.conf
isisd:     isisd.conf
babeld:    babeld.conf

Untuk membuat file konfigurasi, yang paling sederhana adalah mengcopy file dari /usr/share/doc/quagga/examples/ sebagai berikut: 

cp /usr/share/doc/quagga/examples/vtysh.conf.sample /etc/quagga/vtysh.conf
cp /usr/share/doc/quagga/examples/zebra.conf.sample /etc/quagga/zebra.conf
cp /usr/share/doc/quagga/examples/bgpd.conf.sample /etc/quagga/bgpd.conf
cp /usr/share/doc/quagga/examples/ripd.conf.sample /etc/quagga/ripd.conf
cp /usr/share/doc/quagga/examples/ripngd.conf.sample /etc/quagga/ripngd.conf
cp /usr/share/doc/quagga/examples/ospfd.conf.sample /etc/quagga/ospfd.conf
cp /usr/share/doc/quagga/examples/ospf6d.conf.sample  /etc/quagga/ospf6d.conf
cp /usr/share/doc/quagga/examples/isisd.conf.sample /etc/quagga/isisd.conf
cp /usr/share/doc/quagga/examples/babeld.conf.sample /etc/quagga/babeld.conf

Sebetulnya kita dapat saja membuat file .conf kosong. Jika ini dilakukan, maka kita tidak dapat telnet ke daemon, kita perlu mengkonfigurasi ijin telnet dengan vtsh.

Selanjutnya, kita perlu memperbaiki user dan group agar sesuai dengan quagga dan quaggavty kepada file yang ada di dalam folder /etc/quagga: 

chown quagga.quaggavty /etc/quagga/*.conf
chmod 640 /etc/quagga/*.conf

Restart layanan Quagga : 

# /etc/init.d/quagga restart


DEBIAN.CONF FILE

Default dari Quagga daemon akan mendengarkan interface loopback di 127.0.0.1. Artinya kita hanya bisa telnet di address 127.0.0.1 dan tidak bisa di akses secara remore.

Jika kita ingin telnet ke Quagga daemon dari remote, kita dapat mengedit file /etc/quagga/debian.conf. Kita dapat memasukan IP address yang di di telnet atau membuang semua opsi -A.

Contoh:

  • daemon ospfd mendengarkan pada IP address 127.0.0.1 dan 192.168.1.104.
ospfd_options=" --daemon -A 127.0.0.1 192.168.1.104"
  • daemon zebra mendengarkan semua IP address di interface Linux. Lebih di rekomendasikan untuk memfilter siapa yang dapat mengakses router.
zebra_options=" --daemon "

Berikut adalah rekomendasi file debian.conf: 

#vim /etc/quagga/debian.conf

# If this option is set the /etc/init.d/quagga script automatically loads
# the config via "vtysh -b" when the servers are started.
# Check /etc/pam.d/quagga if you intend to use "vtysh"!
#
vtysh_enable=yes
zebra_options=" --daemon -A 127.0.01"
bgpd_options="  --daemon -A 127.0.01"
ospfd_options=" --daemon -A 127.0.01"
ospf6d_options="--daemon -A ::1"
ripd_options="  --daemon -A 127.0.01"
ripngd_options="--daemon -A ::1"
isisd_options=" --daemon -A 127.0.01"
babeld_options=" --daemon -A 127.0.01"

Konfigurasi "vtysh_enable=yes" dibutuhkan untuk mengakses router Quagga menggunakan vtysh.

Restart layanan Quagga 

#/etc/init.d/quagga restart

VTYSH

Kita bisa mengakses daemon di Quagga dengan cara telnet ke port masing-masing daemon. Port tersebut adalah: 


zebra           2601/tcp                        # zebra vty
ripd            2602/tcp                        # ripd vty (zebra)
ripngd          2603/tcp                        # ripngd vty (zebra)
ospfd           2604/tcp                        # ospfd vty (zebra)
bgpd            2605/tcp                        # bgpd vty (zebra)
ospf6d          2606/tcp                        # ospf6d vty (zebra)
ospfapi         2607/tcp                        # OSPF-API
isisd           2608/tcp                        # ISISd vty (zebra)


Sebagai contoh, untuk akses ke daemon ospfd: 

telnet localhost 2604

atau 

telnet localhost ospfd

Akan sangat tidak praktis untuk mengkonfigurasi router dengan cara telnet ke masing-masing daemon secara terpisah, oleh karenanya dibuatlah vtysh untuk mengkonfigurasi segala sesuatu di satu interface.

Untuk mmenggunakan vtysh, kita pertama-tama perlu membuat file konfigurasi sebagai berikut: 

cp /usr/share/doc/quagga/examples/vtysh.conf.sample /etc/quagga/vtysh.conf

Isinya /etc/quagga/vtysh.conf 

!
! Sample
!
! service integrated-vtysh-config
hostname quagga-router
username root nopassword
!

Betulkan ijin dan restart Quagga: 

chown quagga.quaggavty /etc/quagga/*.conf
chmod 640 /etc/quagga/*.conf
/etc/init.d/quagga restart

In the example above the "service integrated-vtysh-config" setting has been disabled (recommended). In this case, when you save the config under vtysh, it will be stored in separate files depending on the protocols you activated. Below, an example where the Quagga configuration is saved under vtysh. (The zebra and ospfd daemons have been enabled.) 

#vtysh
quagga-router#write
Configuration saved to /etc/quagga/zebra.conf
Configuration saved to /etc/quagga/ospfd.conf

If you activate "service integrated-vtysh-config", the configuration under vtysh will be saved in one file called Quagga.conf in the /etc/quagga/ directory. With this setting, when you access a daemon via telnet, the daemon will look first to the Quagga.conf file before looking for its own file. This means that, when you telnet a device, there can be a difference between what you see after the "show run" command and the content of the associated file, for example zebra.conf. 

#vtysh
quagga-router#write
Configuration saved to /etc/quagga/Quagga.conf

It is recommended to disable "service integrated-vtysh-config" because if this setting is enabled and in case of a syntax error in the Quagga.conf file, this can lead to all your daemons being unable to start up. This will not be case when "service integrated-vtysh-config" is disabled because the configurations are stored in separate files.

Check that the default "vtysh_enable=yes" setting are configured in your /etc/quagga/debian.conf file. You can read the previous paragraph about the debian.conf file to get more information.

Then it's useful to add the "VTYSH_PAGER=more" setting in your /etc/environment file, otherwise you will see an unfriendly "(END)" blinking in the left-down corner of the screen each time your enter a command and will need to press the "q" key to continue. 

#echo VTYSH_PAGER=more > /etc/environment

Log off and log on to enable the environment setting. You can now access the Quagga router with the vtysh command: 

# vtysh

Hello, this is Quagga (version 0.99.22).
Copyright 1996-2005 Kunihiro Ishiguro, et al.

ubuntu#

Jika kita ingin menjalankan perintah Quagga dari Shell Linux, lakukan: 

vtysh -c "command"

Contoh: 

vtysh -c "show ip route"

akan menampilkan tabel routing.

You can use Ping and traceroute to perform connectivity checks from the vtysh prompt. Of course, these two programs need to be installed on the Linux machine. Ping is generally installed by default but traceroute often not. To install traceroute: 

#apt-get install traceroute

IP FORWARDING

IP forwarding dibutuhkan untuk mentransfer paket antar interface di sebuah sistem Linux. 

echo "1" > /proc/sys/net/ipv4/ip_forward

Perintah di atas akan menambahkan nilai "1" dalam file /proc/sys/net/ipv4/ip_forward dan mengaktifkan IP forwarding. jika kita menginginkan agar IP forwarding tetap ada saat Linux reboot, lakukan 

echo "net.ipv4.ip_forward = 1" >> /etc/sysctl.conf

Jika juga dapat mencek status ip_forwarding di router Quagga, menggunakan perintah: 

show ip forwarding

Akan keluar 

IP forwarding is on

Jika IP forwarding di aktifkan.

SPEED/DUPLEX

It is not possible to set the duplex and speed settings on the Quagga plateform. You have to configure them at the Linux level. Use the interface configuration tutorial for assistance.

Pranala Menarik

Retrieved from "https://onnocenter.or.id/wiki/index.php?title=TCP/IP:_Quagga_Bagaimana_cara_menggunakan&oldid=38721"