Difference between revisions of "UBNT: openwrt"
Jump to navigation
Jump to search
Onnowpurbo (talk | contribs) |
Onnowpurbo (talk | contribs) |
||
| Line 6: | Line 6: | ||
WARNING: penggunaan firmware ini akan men-disable beberapa fungsi device, seperti LED dan Ubiquiti Web interface. Kita dapat mengembalikannya melalui “Recovery of Ubiquiti firmware” | WARNING: penggunaan firmware ini akan men-disable beberapa fungsi device, seperti LED dan Ubiquiti Web interface. Kita dapat mengembalikannya melalui “Recovery of Ubiquiti firmware” | ||
| + | ==Download OpenWRT== | ||
Download OpenWRT firmware untuk Ubiquiti dari | Download OpenWRT firmware untuk Ubiquiti dari | ||
| + | http://downloads.openwrt.org/snapshots/trunk/atheros/ | ||
| + | Nano2 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt2-squashfs.bin | ||
| + | Pico2 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt2-pico2-squashfs.bin | ||
| + | Nano5 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt5-squashfs.bin | ||
| − | + | ==Flash Update== | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Steps | Steps | ||
| Line 35: | Line 29: | ||
Once you finish these steps your device will have the OpenWRT firmware loaded. Then point your web browser at 192.168.1.1 and proceed by setting a password for the root (administrative) account. | Once you finish these steps your device will have the OpenWRT firmware loaded. Then point your web browser at 192.168.1.1 and proceed by setting a password for the root (administrative) account. | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | + | ==Prosedur Recovery Firmware== | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| + | * [[UBNT: Rebuild Firmware | Kita dapat merecover AirOS firmware melalui prosedur recovery firmware]] | ||
==Referensi== | ==Referensi== | ||
Revision as of 08:51, 21 July 2012
Sumber: http://wiki.ubnt.com/Installing_OpenWRT_on_NanoStations/Bullets
Berikut adalah prosedur untuk mem-flash Ubiquiti Bullet 2 atau Nano2/Loco2. Prosedur ini akan mengganti AirOS firmware dengan OpenWRT firmware.
WARNING: penggunaan firmware ini akan men-disable beberapa fungsi device, seperti LED dan Ubiquiti Web interface. Kita dapat mengembalikannya melalui “Recovery of Ubiquiti firmware”
Download OpenWRT
Download OpenWRT firmware untuk Ubiquiti dari
http://downloads.openwrt.org/snapshots/trunk/atheros/ Nano2 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt2-squashfs.bin Pico2 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt2-pico2-squashfs.bin Nano5 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt5-squashfs.bin
Flash Update
Steps
- First of all, disconnect the Ethernet cable from Pico, Bullet2 or Nano/Loco2. - Connect the Ethernet Cable and immediately press the Reset button (near the device’s RJ45 connector) for 10 seconds. - Make sure that device responds to pinging (command: ping 192.168.1.20, by default). If not, please repeat previous steps. - Using the TFTP client, upload the firmware file (extension .bin) to the Bullet2 or Nano/Loco2 IP address (192.168.1.20, by default). If the device doesn’t accept the firmware filename, rename it to “flash_update”. - Signal LEDs will be blinking during firmware upgrade. - Wait for about 7 minutes (Warning: Do not disconnect the Ethernet cable during procedure).
Configuring IP addressl
Once you finish these steps your device will have the OpenWRT firmware loaded. Then point your web browser at 192.168.1.1 and proceed by setting a password for the root (administrative) account.
Prosedur Recovery Firmware
Referensi
- http://wiki.ubnt.com/Installing_OpenWRT_on_NanoStations/Bullets
- http://wiki.openwrt.org/toh/ubiquiti/nanostation
- http://downloads.openwrt.org/snapshots/trunk/atheros/