Difference between revisions of "OpenBTS: RangeNetwork Hardware"
Onnowpurbo (talk | contribs) (New page: Range Networks SDR1 Open Source Software-Defined Radio The Range Networks SDR1 consists of two individual PCBs that work in tandem, referred to as the SDR module and the RF module (or boa...) |
Onnowpurbo (talk | contribs) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 3: | Line 3: | ||
The Range Networks SDR1 consists of two individual PCBs that work in tandem, referred to as the SDR module and the RF module (or board). The SDR module provides signal processing and digital data transfer between the RF signals and the host. The RF module provides the wireless transmission of the data. The SDR and RF module boards are each on a 5.5" x 3.25" PCB outline. This is a stacked design with a single interface connector between them. The RF module uses the same PCB layout with different component stuffing options and is capable of supporting the following frequency bands: 850, 900, 1800, 1900 MHz. The SDR1 is based in large part on the USRP1 design. | The Range Networks SDR1 consists of two individual PCBs that work in tandem, referred to as the SDR module and the RF module (or board). The SDR module provides signal processing and digital data transfer between the RF signals and the host. The RF module provides the wireless transmission of the data. The SDR and RF module boards are each on a 5.5" x 3.25" PCB outline. This is a stacked design with a single interface connector between them. The RF module uses the same PCB layout with different component stuffing options and is capable of supporting the following frequency bands: 850, 900, 1800, 1900 MHz. The SDR1 is based in large part on the USRP1 design. | ||
| − | + | Range Networks SDR1 terdiri dari dua PCB yang bekerja bersama-sama, disebut sebagai modul SDR dan modul RF. Modul SDR menyediakan pemrosesan sinyal dan transfer data digital antara sinyal RF dan host. Modul RF menyediakan transmisi wireless untuk komunikasi data. Board modul SDR dan RF masing-masing memiliki ukuran PCB 5,5 inchi x 3,25 inchi. Ini adalah desain bertumpuk dengan konektor antarmuka tunggal di antara mereka. Modul RF menggunakan tata letak PCB yang sama dengan opsi isian komponen yang berbeda dan mampu mendukung pita frekuensi berikut: 850, 900, 1800, 1900 MHz. SDR1 sebagian besar didasarkan pada desain USRP1. | |
| − | + | ||
| − | + | ==Cek USB== | |
| − | + | ||
| − | + | Pakai | |
| − | + | ||
| − | + | lsusb | |
| − | + | ||
| − | + | Akan keluar | |
| − | + | ||
| + | Bus 001 Device 003: ID fffe:0002 | ||
| Line 22: | Line 23: | ||
* https://github.com/RangeNetworks/hardware-designs | * https://github.com/RangeNetworks/hardware-designs | ||
| + | |||
| + | |||
| + | ==Pranala Menarik== | ||
| + | |||
| + | * [[OpenBTS]] | ||
Latest revision as of 07:20, 8 May 2019
Range Networks SDR1 Open Source Software-Defined Radio
The Range Networks SDR1 consists of two individual PCBs that work in tandem, referred to as the SDR module and the RF module (or board). The SDR module provides signal processing and digital data transfer between the RF signals and the host. The RF module provides the wireless transmission of the data. The SDR and RF module boards are each on a 5.5" x 3.25" PCB outline. This is a stacked design with a single interface connector between them. The RF module uses the same PCB layout with different component stuffing options and is capable of supporting the following frequency bands: 850, 900, 1800, 1900 MHz. The SDR1 is based in large part on the USRP1 design.
Range Networks SDR1 terdiri dari dua PCB yang bekerja bersama-sama, disebut sebagai modul SDR dan modul RF. Modul SDR menyediakan pemrosesan sinyal dan transfer data digital antara sinyal RF dan host. Modul RF menyediakan transmisi wireless untuk komunikasi data. Board modul SDR dan RF masing-masing memiliki ukuran PCB 5,5 inchi x 3,25 inchi. Ini adalah desain bertumpuk dengan konektor antarmuka tunggal di antara mereka. Modul RF menggunakan tata letak PCB yang sama dengan opsi isian komponen yang berbeda dan mampu mendukung pita frekuensi berikut: 850, 900, 1800, 1900 MHz. SDR1 sebagian besar didasarkan pada desain USRP1.
Cek USB
Pakai
lsusb
Akan keluar
Bus 001 Device 003: ID fffe:0002
Referensi