Difference between revisions of "OSPF"

From OnnoWiki
Jump to navigation Jump to search
(New page: '''Open Shortest Path First''' ('''OSPF''') is a link-state routing protocol for Internet Protocol (IP) networks. It uses a link state routing ...)
 
 
(3 intermediate revisions by the same user not shown)
Line 145: Line 145:
 
# Loading State
 
# Loading State
 
# Full State  (Routers are “fully adjacent”)
 
# Full State  (Routers are “fully adjacent”)
 +
 +
 +
 +
 +
==Pranala Menarik==
 +
 +
* [[OSPF: Konsep Sederhana]]
 +
* [[OSPF: dengan authentikasi]]
 +
* [[OSPF: type 1 dan type 2]]
 +
 +
* [[TCP/IP: Advanced Routing]]
 +
* [[Quagga]]
 +
* [[Mikrotik]]
 +
* [[Cisco]]
 +
* [[Juniper]]
 +
* [[BIRD: Routing]]
 +
* [[IPv6]]

Latest revision as of 16:01, 7 January 2019

Open Shortest Path First (OSPF) is a link-state routing protocol for Internet Protocol (IP) networks. It uses a link state routing algorithm and falls into the group of interior routing protocols, operating within a single autonomous system (AS). It is defined as OSPF Version 2 in RFC 2328 (1998) for IPv4 The updates for IPv6 are specified as OSPF Version 3 in RFC 5340 (2008).

OSPF is perhaps the most widely used interior gateway protocol (IGP) in large enterprise networks. IS-IS, another link-state dynamic routing protocol, is more common in large service provider networks. The most widely used exterior gateway protocol is the Border Gateway Protocol (BGP), the principal routing protocol between autonomous systems on the Internet.

Overview

OSPF is an interior gateway protocol that routes Internet Protocol (IP) packets solely within a single routing domain (autonomous system). It gathers link state information from available routers and constructs a topology map of the network. The topology determines the routing table presented to the Internet Layer which makes routing decisions based solely on the destination IP address found in IP packets. OSPF was designed to support variable-length subnet masking (VLSM) or Classless Inter-Domain Routing (CIDR) addressing models.

OSPF detects changes in the topology, such as link failures, and converges on a new loop-free routing structure within seconds. It computes the shortest path tree for each route using a method based on Dijkstra's algorithm, a shortest path first algorithm.

The OSPF routing policies to construct a route table are governed by link cost factors (external metrics) associated with each routing interface. Cost factors may be the distance of a router (round-trip time), network throughput of a link, or link availability and reliability, expressed as simple unitless numbers. This provides a dynamic process of traffic load balancing between routes of equal cost.

An OSPF network may be structured, or subdivided, into routing areas to simplify administration and optimize traffic and resource utilization. Areas are identified by 32-bit numbers, expressed either simply in decimal, or often in octet-based dot-decimal notation, familiar from IPv4 address notation.

By convention, area 0 (zero) or 0.0.0.0 represents the core or backbone region of an OSPF network. The identifications of other areas may be chosen at will; often, administrators select the IP address of a main router in an area as the area's identification. Each additional area must have a direct or virtual connection to the backbone OSPF area. Such connections are maintained by an interconnecting router, known as area border router (ABR). An ABR maintains separate link state databases for each area it serves and maintains summarized routes for all areas in the network.

OSPF does not use a TCP/IP transport protocol (UDP, TCP), but is encapsulated directly in IP datagrams with protocol number 89. This is in contrast to other routing protocols, such as the Routing Information Protocol (RIP), or the Border Gateway Protocol (BGP). OSPF handles its own error detection and correction functions.

OSPF uses multicast addressing for route flooding on a broadcast domain. For non-broadcast networks special provisions for configuration facilitate neighbor discovery. OSPF multicast IP packets never traverse IP routers (never traverse Broadcast Domains), they never travel more than one hop. OSPF reserves the multicast addresses 224.0.0.5 for IPv4 or FF02::5 for IPv6 (all SPF/link state routers, also known as AllSPFRouters) and 224.0.0.6 for IPv4 or FF02::6 for IPv6 (all Designated Routers, AllDRouters), as specified in RFC 2328 and RFC 5340.

For routing multicast IP traffic, OSPF supports the Multicast Open Shortest Path First protocol (MOSPF) as defined in RFC 1584. Cisco does not include MOSPF in their OSPF implementations. PIM (Protocol Independent Multicast) in conjunction with OSPF or other IGPs, (Interior Gateway Protocol), is widely deployed.

The OSPF protocol, when running on IPv4, can operate securely between routers, optionally using a variety of authentication methods to allow only trusted routers to participate in routing. OSPFv3, running on IPv6, no longer supports protocol-internal authentication. Instead, it relies on IPv6 protocol security (IPsec).

OSPF version 3 introduces modifications to the IPv4 implementation of the protocol. Except for virtual links, all neighbor exchanges use IPv6 link-local addressing exclusively. The IPv6 protocol runs per link, rather than based on the subnet. All IP prefix information has been removed from the link-state advertisements and from the Hello discovery packet making OSPFv3 essentially protocol-independent. Despite the expanded IP addressing to 128-bits in IPv6, area and router Identifications are still based on 32-bit values.

Neighbor relationships

Routers in the same broadcast domain or at each end of a point-to-point telecommunications link form adjacencies when they have detected each other. This detection occurs when a router identifies itself in a hello OSPF protocol packet. This is called a two-way state and is the most basic relationship. The routers in an Ethernet or frame relay network select a designated router (DR) and a backup designated router (BDR) which act as a hub to reduce traffic between routers. OSPF uses both unicast and multicast to send "hello packets" and link state updates.

As a link state routing protocol, OSPF establishes and maintains neighbor relationships in order to exchange routing updates with other routers. The neighbor relationship table is called an adjacency database in OSPF. Provided that OSPF is configured correctly, OSPF forms neighbor relationships only with the routers directly connected to it. In order to form a neighbor relationship between two routers, the interfaces used to form the relationship must be in the same area. Generally an interface is only configured in a single area, however you can configure an interface to belong to multiple areas. In the second area, such an interface must be configured as a secondary interface. (A neighbor state simulation shows how neighbor state changes from Down to Full Adjacency progressively with exchanging Hello, DD, Request, Update, and Ack packets).

Area types

An OSPF domain is divided into areas that are labeled with 32-bit area identifiers. The area identifiers are commonly, but not always, written in the dot-decimal notation of an IPv4 address. However, they are not IP addresses and may duplicate, without conflict, any IPv4 address. The area identifiers for IPv6 implementations of OSPF (OSPFv3) also use 32-bit identifiers written in the same notation. While most OSPF implementations will right-justify an area number written in a format other than dotted decimal format (e.g., area 1), it is wise to always use dotted-decimal formats. Most implementations expand area 1 to the area identifier 0.0.0.1, but some have been known to expand it as 1.0.0.0.

Areas are logical groupings of hosts and networks, including their routers having interfaces connected to any of the included networks. Each area maintains a separate link state database whose information may be summarized towards the rest of the network by the connecting router. Thus, the topology of an area is unknown outside of the area. This reduces the amount of routing traffic between parts of an autonomous system.

Several special area types are defined.

Backbone area

The backbone area (also known as area 0 or area 0.0.0.0) forms the core of an OSPF network. All other areas are connected to it, and inter-area routing happens via routers connected to the backbone area and to their own associated areas. It is the logical and physical structure for the 'OSPF domain' and is attached to all nonzero areas in the OSPF domain. Note that in OSPF the term Autonomous System Boundary Router (ASBR) is historic, in the sense that many OSPF domains can coexist in the same Internet-visible autonomous system, RFC1996.

The backbone area is responsible for distributing routing information between nonbackbone areas. The backbone must be contiguous, but it does not need to be physically contiguous; backbone connectivity can be established and maintained through the configuration of virtual links.

All OSPF areas must connect to the backbone area. This connection, however, can be through a virtual link. For example, assume area 0.0.0.1 has a physical connection to area 0.0.0.0. Further assume that area 0.0.0.2 has no direct connection to the backbone, but this area does have a connection to area 0.0.0.1. Area 0.0.0.2 can use a virtual link through the transit area 0.0.0.1 to reach the backbone. To be a transit area, an area has to have the transit attribute, so it cannot be stubby in any way.

Stub area

A stub area is an area which does not receive route advertisements external to the autonomous system (AS) and routing from within the area is based entirely on a default route. An ABR deletes type 4, 5 LSAs from internal routers, sends them a default route of 0.0.0.0 and turns itself into a default gateway. This reduces LSDB and routing table size for internal routers.

Modifications to the basic concept of stub areas exist in the not-so-stubby area (NSSA). In addition, several other proprietary variations have been implemented by systems vendors, such as the totally stubby area (TSA) and the NSSA not so stubby area, both an extension in Cisco Systems routing equipment.

Not-so-stubby area

A not-so-stubby area (NSSA) is a type of stub area that can import autonomous system external routes and send them to other areas, but still cannot receive AS-external routes from other areas. NSSA is an extension of the stub area feature that allows the injection of external routes in a limited fashion into the stub area. A case study simulates an NSSA getting around the Stub Area problem of not being able to import external addresses. It visualizes the following activities: the ASBR imports external addresses with a type 7 LSA, the ABR converts a type 7 LSA to type 5 and floods it to other areas, the ABR acts as an "ASBR" for other areas. The ABRs do not take type 5 LSAs and then convert to type 7 LSAs for the area.Here is the whole idea to do it.

Proprietary extensions

Several vendors (Cisco, Juniper, Alcatel-Lucent, Huawei, Quagga), now implement the below two extensions to stub and NSSA area and although not covered by RFC they are considered by many to be standard features in OSPF implementations.

Totally stubby area
A totally stubby area is similar to a stub area. However, this area does not allow summary routes in addition to not having external routes, that is, inter-area (IA) routes are not summarized into totally stubby areas. The only way for traffic to get routed outside of the area is a default route which is the only Type-3 LSA advertised into the area. When there is only one route out of the area, fewer routing decisions have to be made by the route processor, which lowers system resource utilization.
Occasionally, it is said that a TSA can have only one ABR.
NSSA totally stubby area
An addition to the standard functionality of an NSSA, the totally stubby NSSA is an NSSA that takes on the attributes of a TSA, meaning that type 3 and 4 summary routes are not flooded into this type of area. It is also possible to declare an area both totally stubby and not-so-stubby, which means that the area will receive only the default route from area 0.0.0.0, but can also contain an autonomous system boundary router (ASBR) that accepts external routing information and injects it into the local area, and from the local area into area 0.0.0.0.
Redistribution into an NSSA area creates a special type of LSA known as type 7, which can exist only in an NSSA area. An NSSA ASBR generates this LSA, and an NSSA ABR router translates it into type 5 LSA which gets propagated into the OSPF domain.

A newly acquired subsidiary is one example of where it might be suitable for an area to be simultaneously not-so-stubby and totally stubby if the practical place to put an ASBR is on the edge of a totally stubby area. In such a case, the ASBR does send externals into the totally stubby area, and they are available to OSPF speakers within that area. In Cisco's implementation, the external routes can be summarized before injecting them into the totally stubby area. In general, the ASBR should not advertise default into the TSA-NSSA, although this can work with extremely careful design and operation, for the limited special cases in which such an advertisement makes sense.

By declaring the totally stubby area as NSSA, no external routes from the backbone, except the default route, enter the area being discussed. The externals do reach area 0.0.0.0 via the TSA-NSSA, but no routes other than the default route enter the TSA-NSSA. Routers in the TSA-NSSA send all traffic to the ABR, except to routes advertised by the ASBR.

Transit area

A transit area is an area with two or more OSPF border routers and is used to pass network traffic from one adjacent area to another. The transit area does not originate this traffic and is not the destination of such traffic.

Path preference

OSPF uses path cost as its basic routing metric, which was defined by the standard not to equate to any standard value such as speed, so the network designer could pick a metric important to the design. In practice, it is determined by the speed (bandwidth) of the interface addressing the given route, although that tends to need network-specific scaling factors now that links faster than 100 Mbit/s are common. Cisco uses a metric like 10^8/bandwidth (the base value, 10^8 by default, can be adjusted). So, a 100Mbit/s link will have a cost of 1, a 10Mbit/s a cost of 10 and so on. But for links faster than 100Mbit/s, the cost would be <1.

Metrics, however, are only directly comparable when of the same type. Four types of metrics are recognized. An intra-area route is always preferred to an External route regardless of metric. In decreasing preference, these types are:

  1. Intra-area
  2. Inter-area
  3. External Type 1, which includes both the external path cost and the sum of internal path costs to the ASBR that advertises the route,
  4. External Type 2, the value of which is solely that of the external path cost

Traffic engineering

OSPF-TE is an extension to OSPF extending the expressivity to allow for traffic engineering and use on non-IP networks (RFC 3630). More information about the topology can be exchanged using opaque LSA carrying type-length-value elements. These extensions allow OSPF-TE to run completely out of band of the data plane network. This means that it can also be used on non-IP networks, such as optical networks.

OSPF-TE is used in GMPLS networks as a means to describe the topology over which GMPLS paths can be established. GMPLS uses its own path setup and forwarding protocols, once it has the full network map.

In the Resource Reservation Protocol (RSVP), OSPF-TE is used for recording and flooding RSVP signaled bandwidth reservations for label switched paths within the link-state database.

Other extensions

RFC 3717 documents work in optical routing for IP, based on "constraint-based" extensions to OSPF and IS-IS.

OSPF router types

OSPF defines the following router types:

  • Area border router (ABR)
  • Autonomous system boundary router (ASBR)
  • Internal router (IR)
  • Backbone router (BR)

The router type is an attribute of an OSPF process. A given physical router may have one or more OSPF processes. For example, a router that is connected to more than one area, and which receives routes from a BGP process connected to another AS, is both an area border router and an autonomous system boundary router.

Each router has an identifier, customarily written in the dotted decimal format (e.g., 1.2.3.4) of an IP address. This identifier must be established in every OSPF instance. If not explicitly configured, the highest logical IP address will be duplicated as the router identifier. However, since the router identifier is not an IP address, it does not have to be a part of any routable subnet in the network, and often isn't to avoid confusion.

These router types should not be confused with the terms designated router (DR), or backup designated router (BDR), which are attributes of a router interface, not the router itself.

Area border router

An area border router (ABR) is a router that connects one or more areas to the main backbone network. It is considered a member of all areas it is connected to. An ABR keeps multiple copies of the link-state database in memory, one for each area to which that router is connected.

Autonomous system boundary router

An autonomous system boundary router (ASBR) is a router that is connected to more than one Routing protocol and that exchanges routing information with routers in other protocols. ASBRs typically also run an exterior routing protocol (e.g., BGP), or use static routes, or both. An ASBR is used to distribute routes received from other, external ASs throughout its own autonomous system. An ASBR creates External LSAs for external addresses and floods them to all areas via ABR. Routers in other areas use ABRs as next hops to access external addresses. Then ABRs forward packets to the ASBR that announces the external addresses.

Internal router

An internal router is a router that has OSPF neighbor relationships with interfaces in the same area. An internal router has all its interfaces in a single area.

Designated router

A designated router (DR) is the router interface elected among all routers on a particular multiaccess network segment, generally assumed to be broadcast multiaccess. The basic neighbor discovery process (Hello), flooding (224.0.0.6), DR election (priority, RID). Special techniques, often vendor-dependent, may be needed to support the DR function on nonbroadcast multiaccess (NBMA) media. It is usually wise to configure the individual virtual circuits of a NBMA subnet as individual point-to-point lines; the techniques used are implementation-dependent.

Do not confuse the DR with an OSPF router type. A given physical router can have some interfaces that are designated (DR), others that are backup designated (BDR), and others that are non-designated. If no router is DR or BDR on a given subnet, the BDR is first elected, and then a second election is held for the DR. s a step-by-step DR election example: How neighbor list, neighbor state, DR, and BDR are changed when receiving Hello) The DR is elected based on the following default criteria:

  • If the priority setting on an OSPF router is set to 0, that means it can NEVER become a DR or BDR (Backup Designated Router).
  • When a DR fails and the BDR takes over, there is another election to see who becomes the replacement BDR.
  • The router sending the Hello packets with the highest priority wins the election.
  • If two or more routers tie with the highest priority setting, the router sending the Hello with the highest RID (Router ID) wins. NOTE: a RID is the highest logical (loopback) IP address configured on a router, if no logical/loopback IP address is set then the Router uses the highest IP address configured on its active interfaces. (e.g. 192.168.0.1 would be higher than 10.1.1.2).
  • Usually the router with the second highest priority number becomes the BDR.
  • The priority values range between 0 - 255, with a higher value increasing its chances of becoming DR or BDR.
  • IF a HIGHER priority OSPF router comes online AFTER the election has taken place, it will not become DR or BDR until (at least) the DR and BDR fail.
  • If the current DR 'goes down' the current BDR becomes the new DR and a new election takes place to find another BDR. If the new DR then 'goes down' and the original DR is now available, still previously chosen BDR will become DR.

DR's exist for the purpose of reducing network traffic by providing a source for routing updates. The DR maintains a complete topology table of the network and sends the updates to the other routers via multicast. All routers in a multi-access network segment will form a slave/master relationship with the DR. They will form adjacencies with the DR and BDR only. Every time a router sends an update, it sends it to the DR and BDR on the multicast address 224.0.0.6. The DR will then send the update out to all other routers in the area, to the multicast address 224.0.0.5. This way all the routers do not have to constantly update each other, and can rather get all their updates from a single source. The use of multicasting further reduces the network load. DRs and BDRs are always setup/elected on OSPF broadcast networks. DR's can also be elected on NBMA (Non-Broadcast Multi-Access) networks such as Frame Relay or ATM. DRs or BDRs are not elected on point-to-point links (such as a point-to-point WAN connection) because the two routers on either sides of the link must become fully adjacent and the bandwidth between them cannot be further optimized. DR and non-DR routers evolve from 2-way to full adjacency relationships by exchanging DD, Request, and Update.

Backup designated router

A backup designated router (BDR) is a router that becomes the designated router if the current designated router has a problem or fails. The BDR is the OSPF router with second highest priority at the time of the last election.

OSPF Router States

  1. Down State – No Hello received
  2. Init State – Hello received, but not with this router’s Router ID
 e.g. “Hi, my name is Carlos.”              “Hi, my name is Maria.”
  1. Two-way State – Hello received, and with this router’s Router ID
 e.g.  “Hi, Maria, my name is Carlos.”   “Hi, Carlos, my name is Maria.”

  1. ExStart State with DR and BDR
 Two-way State with all other routers
  1. Exchange State
  2. Loading State
  3. Full State (Routers are “fully adjacent”)



Pranala Menarik