Difference between revisions of "Linux: Interface BONDING"

From OnnoWiki
Jump to navigation Jump to search
 
(8 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
Sumber: https://help.ubuntu.com/community/UbuntuBonding
 
Sumber: https://help.ubuntu.com/community/UbuntuBonding
 +
 +
'''WARNING'''
 +
Jika di lakukan di Ubuntu 18.04 perlu di delete referensi ke interface jaringan (spt enp3s0) di
 +
 +
* /etc/netplan/
 +
* /etc/cloud/cloud.cfg.d
  
  
 
==Install Pendukung==
 
==Install Pendukung==
  
  apt install ifupdown  
+
  apt install ifupdown ifenslave
 
 
  
 
==Aktifkan Module==
 
==Aktifkan Module==
Line 28: Line 33:
  
 
  sudo vi /etc/network/interfaces
 
  sudo vi /etc/network/interfaces
 
 
  
 
  # enp3s0 is manually configured, and slave to the "bond0" bonded NIC
 
  # enp3s0 is manually configured, and slave to the "bond0" bonded NIC
Line 35: Line 38:
 
  iface enp3s0 inet manual  
 
  iface enp3s0 inet manual  
 
     bond-master bond0
 
     bond-master bond0
    bond-primary enp3s0
+
#    bond-primary enp3s0
 
   
 
   
  # enp4s3 ditto, thus creating a 2-link bond.
+
  # enp4s0 ditto, thus creating a 2-link bond.
  auto enp4s3
+
  auto enp4s0
  iface enp4s3 inet manual
+
  iface enp4s0 inet manual
 
     bond-master bond0
 
     bond-master bond0
 
   
 
   
Line 46: Line 49:
 
  auto bond0
 
  auto bond0
 
  iface bond0 inet static
 
  iface bond0 inet static
     address 192.168.1.10
+
     address 192.168.0.9
     gateway 192.168.1.1
+
     gateway 192.168.0.223
 
     netmask 255.255.255.0
 
     netmask 255.255.255.0
    bond-mode active-backup
+
#    bond-mode active-backup
    bond-miimon 100
+
#    bond-miimon 100
     bond-slaves none
+
#    bond-slaves none
 +
     bond-slaves enp3s0 enp4s0
 +
 
 +
 
 +
Edit
 +
 
 +
vi /etc/modprobe.d/bonding
 +
 
 +
alias bond0 bonding
  
 
==Aktifasi Bonding==
 
==Aktifasi Bonding==
Line 57: Line 68:
 
  sudo start networking
 
  sudo start networking
  
 +
atau
 +
 +
/etc/init.d/networking restart
  
 
Atau
 
Atau

Latest revision as of 07:51, 13 December 2019

Sumber: https://help.ubuntu.com/community/UbuntuBonding

WARNING Jika di lakukan di Ubuntu 18.04 perlu di delete referensi ke interface jaringan (spt enp3s0) di

  • /etc/netplan/
  • /etc/cloud/cloud.cfg.d


Install Pendukung

apt install ifupdown ifenslave

Aktifkan Module

sudo su
vi /etc/modules
# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.
 
bonding mode=6 miimon=100

Aktifkan module

modprobe --first-time bonding
modprobe bonding
modinfo bonding | more

Edit Interface

sudo vi /etc/network/interfaces
# enp3s0 is manually configured, and slave to the "bond0" bonded NIC
auto enp3s0
iface enp3s0 inet manual 
    bond-master bond0
#    bond-primary enp3s0

# enp4s0 ditto, thus creating a 2-link bond.
auto enp4s0
iface enp4s0 inet manual
    bond-master bond0

# bond0 is the bonding NIC and can be used like any other normal NIC.
# bond0 is configured using static network information.
auto bond0
iface bond0 inet static
    address 192.168.0.9
    gateway 192.168.0.223
    netmask 255.255.255.0
#    bond-mode active-backup
#    bond-miimon 100
#    bond-slaves none
    bond-slaves enp3s0 enp4s0


Edit

vi /etc/modprobe.d/bonding
alias bond0 bonding

Aktifasi Bonding

sudo start networking

atau

/etc/init.d/networking restart

Atau

ifup bond0
ifdown bond0

Cek

cat /proc/net/bonding/bond0
ifconfig


Catatan

Mode 0

balance-rr

Round-robin policy: Transmit packets in sequential order from the first available slave through the last. This mode provides load balancing and fault tolerance.

Mode 1

active-backup

Active-backup policy: Only one slave in the bond is active. A different slave becomes active if, and only if, the active slave fails. The bond's MAC address is externally visible on only one port (network adapter) to avoid confusing the switch. This mode provides fault tolerance. The primary option affects the behavior of this mode.

Mode 2

balance-xor

XOR policy: Transmit based on selectable hashing algorithm. The default policy is a simple source+destination MAC address algorithm. Alternate transmit policies may be selected via the xmit_hash_policy option, described below. This mode provides load balancing and fault tolerance.

Mode 3

broadcast

Broadcast policy: transmits everything on all slave interfaces. This mode provides fault tolerance.

Mode 4

802.3ad

IEEE 802.3ad Dynamic link aggregation. Creates aggregation groups that share the same speed and duplex settings. Utilizes all slaves in the active aggregator according to the 802.3ad specification.

Prerequisites:

  • Ethtool support in the base drivers for retrieving the speed and duplex of each slave.
  • A switch that supports IEEE 802.3ad Dynamic link aggregation. Most switches will require some type of configuration to enable 802.3ad mode.

Mode 5

balance-tlb

Adaptive transmit load balancing: channel bonding that does not require any special switch support. The outgoing traffic is distributed according to the current load (computed relative to the speed) on each slave. Incoming traffic is received by the current slave. If the receiving slave fails, another slave takes over the MAC address of the failed receiving slave.

Prerequisites:

  • Ethtool support in the base drivers for retrieving the speed of each slave.

Mode 6

balance-alb

Adaptive load balancing: includes balance-tlb plus receive load balancing (rlb) for IPV4 traffic, and does not require any special switch support. The receive load balancing is achieved by ARP negotiation. The bonding driver intercepts the ARP Replies sent by the local system on their way out and overwrites the source hardware address with the unique hardware address of one of the slaves in the bond such that different peers use different hardware addresses for the server.

Referensi