Difference between revisions of "4G: OpenAirInterface instalasi"

From OnnoWiki
Jump to navigation Jump to search
(Created page with "Sumber: https://hackmd.io/@ChiehChun/SkKj1oRoV/https%3A%2F%2Fhackmd.io%2F%40ChiehChun%2FrJkKmWPlH?type=book ==Referensi== * https://hackmd.io/@ChiehChun/SkKj1oRoV/https%3...")
 
Line 1: Line 1:
 
Sumber: https://hackmd.io/@ChiehChun/SkKj1oRoV/https%3A%2F%2Fhackmd.io%2F%40ChiehChun%2FrJkKmWPlH?type=book
 
Sumber: https://hackmd.io/@ChiehChun/SkKj1oRoV/https%3A%2F%2Fhackmd.io%2F%40ChiehChun%2FrJkKmWPlH?type=book
 +
 +
 +
 +
 +
    Build OAI LTE eNB & EPC BMW Lab.@NTUST
 +
        OAI architecture
 +
        Build OAI LTE on VM
 +
        OAI LTE Testing
 +
            1. Installation on PC
 +
            2. Set up OAI eNB and EPC
 +
            3. RUN OAI
 +
            4. Testing results
 +
 +
OAI architecture
 +
 +
Build OAI LTE on VM
 +
 +
Follow this note for building on the virtual machine
 +
OAI LTE Testing
 +
1. Installation on PC
 +
 +
    Install os
 +
 +
    STEP1: Format USB
 +
    STEP2: Make a bootable USB (Refus)(https://rufus.akeo.ie/)
 +
        Download Rufus 3.1 Portable
 +
        Download ubuntu 14.04.5 .iso
 +
        Open Refus and load ubuntu.iso -> click “START”
 +
    STEP3:
 +
    Insert USB in mini pc and press F2 to enter Bios (Depends on different computer brands)
 +
    STEP4: Move USB to first boot order , and save(F10)
 +
    STEP5: Install ubuntu os
 +
 +
 +
name : oai
 +
password : linux
 +
 +
    Internet setting
 +
 +
    STEP1: Check internet state
 +
 +
oai@oai:~$ ifconfig
 +
 +
 +
Have no internet connection
 +
 +
    STEP2: Editing wired connection
 +
 +
    Select IPV4 Settings
 +
    Method : Manual
 +
 +
    Address : 140.118.121.32
 +
    Netmask : 255.255.255.0
 +
    Gateway : 140.118.121.254
 +
    DNS : 140.118.31.99
 +
    STEP3: oai@oai:~$ ifconfig , check whether connect to internet
 +
 +
2. Set up OAI eNB and EPC
 +
 +
    OAI environment set up and installation
 +
 +
    STEP 1 : Environment/low-latency kernel set up
 +
 +
oai@oai:~$ sudo apt-get update
 +
oai@oai:~$ sudo apt-get install vim
 +
oai@oai:~$ sudo vim /etc/hosts (replace ubuntu to oai.openair4G.eur oai)
 +
oai@oai:~$ sudo reboot
 +
oai@oai:~$ sudo apt-get install git -y  (#install git)
 +
oai@oai:~$ git clone https://gitlab.eurecom.fr/oai/openairinterface5g.git (# clone the eNB/UE source code)
 +
oai@oai:~$ git clone https://gitlab.eurecom.fr/oai/openair-cn.git (# clone the EPC source code)
 +
 +
# if the openair-cn can not clone from Gitlab, try the follow command
 +
oai@oai:~$ git clone https://github.com/OPENAIRINTERFACE/openair-cn.git
 +
 +
oai@oai:~$ cd openair-cn/
 +
oai@oai:~/openair-cn$ git checkout v0.3.2 (# swtich the branch to the one that we gonna use)
 +
oai@oai:~$ sudo apt-get install linux-lowlatency-lts-vivid -y (# Install low-lentency kernel)
 +
oai@oai:~$ sudo apt-get install cpufrequtils (# Set cpu scaling)
 +
oai@oai:~$ sudo vim /etc/default/cpufrequtils
 +
add GOVERNOR="performance" to this file
 +
oai@oai:~$ sudo update-rc.d ondemand disable
 +
oai@oai:~$ dpkg --get-selections | grep linux-image (# remove the kernel we won't used)
 +
oai@oai:~$ sudo apt-get purge linux-image-4.4.0-31-generic linux-image-extra-4.4.0-31-generic linux-image-generic-lts-xenial
 +
oai@oai:~$ sudo update-grub2
 +
 +
    STEP 2 : Reboot and change the kernel to low-latency
 +
 +
@oai:~$sudo reboot
 +
 +
Press esc to setting interface when reboot
 +
 +
Change kernel
 +
 +
    STEP 3 : check uname -a , you will have
 +
 +
    Openair-CN (EPC) installation
 +
 +
    STEP 1 : Build the package for HSS
 +
 +
oai@oai:~$ cd openair-cn/SCRIPTS/
 +
oai@oai:~/openair-cn/SCRIPTS$ sudo ./build_hss -i (# Install the package which is needed from HSS)
 +
 +
    Set MySQL password to “linux”
 +
    Choose apache
 +
    Set phpmyadmin password to “linux”
 +
 +
    STEP 2 : Build the package for EPC ( including MME and SPGW )
 +
 +
oai@oai:~/openair-cn/SCRIPTS$ sudo ./build_epc -i (# Install the package which is needed from epc (including MME and SPGW))
 +
 +
    Openairinterface eNB installation
 +
 +
    STEP 1 : Install the package which is needed from eNB, including UHD driver
 +
 +
oai@oai:~/openair-cn/SCRIPTS$ cd ~/openairinterface5g/cmake_targets/
 +
oai@oai:~/openairinterface5g/cmake_targets$ sudo ./build_oai -I --eNB -x --install-system-files -w USRP
 +
 +
    STEP 2 : Adapt your modification,if you do any modification related to source code
 +
 +
oai@oai:~/openairinterface5g/cmake_targets$ sudo ./build_oai -w USRP -x -c --eNB
 +
 +
    Configuration Setting for connect eNB to EPC
 +
 +
eNB part-
 +
 +
    STEP 1 : Copy the configruation files we will use for eNB
 +
 +
oai@oai:~/openairinterface5g/cmake_targets$ cd ~/openairinterface5g/targets/PROJECTS/GENERIC-LTE-EPC/CONF/
 +
oai@oai:~/openairinterface5g/targets/PROJECTS/GENERIC-LTE-EPC/CONF$ cp enb.band7.tm1.50PRB.usrpb210.conf ~/
 +
oai@oai:~/openairinterface5g/targets/PROJECTS/GENERIC-LTE-EPC/CONF$ cd
 +
oai@oai:~$ vim enb.band7.tm1.50PRB.usrpb210.conf
 +
 +
-> modify eNB configuration
 +
 +
    STEP 2 : Edit configuration
 +
    If git brach is on v0.6.1_tdd, there do NOT have “ENB_IPv4_ADDRESS_FOR_X2C” and “ENB_PORT_FOR_X2C”. And on the branch of v0.6.1_tdd, we do not set the X2C interface. However, the git branch is on the develop/master, there would have “ENB_IPv4_ADDRESS_FOR_X2C” and “ENB_PORT_FOR_X2C” in the NETWORK_INTERFACES.
 +
    And we need to set the X2C address as same as S1U.
 +
 +
        : wq to save
 +
    STEP 3: Record your eth0 ip address
 +
 +
oai@oai:~$ ifconfig
 +
 +
EPC part- (gedit epc.cong.in)
 +
 +
    STEP 4 : Edit EPC configuration
 +
 +
    OAI config format
 +
 +
3. RUN OAI
 +
 +
    step 1 : build epc (Terminal 1)
 +
 +
oai@oai:~/openair-cn/BUILD/EPC$ cd ~/openair-cn/SCRIPTS/
 +
oai@oai:~/openair-cn/SCRIPTS$ sudo ./build_epc -i
 +
oai@oai:~/openair-cn/SCRIPTS$ sudo ./build_epc -c -l
 +
 +
    step 2 : build hss (Terminal 2)
 +
 +
oai@oai:~/openair-cn/SCRIPTS$ sudo ./build_hss -c -l
 +
 +
    STEP 3 : run epc (Terminal 1)
 +
 +
oai@oai:~/openair-cn/SCRIPTS$ sudo ./run_epc -i -r
 +
 +
    STEP 4 : run hss (Terminal 2)
 +
 +
oai@oai:~/openair-cn/SCRIPTS$ sudo ./run_hss
 +
 +
    STEP 5 : run eNB (Terminal 3)
 +
    Mark : Run eNB twice to succeed
 +
 +
oai@oai:~$ cd openairinterface5g/cmake_targets/lte_build_oai/build/
 +
oai@oai:~/openairinterface5g/cmake_targets/lte_build_oai/build$ sudo ifconfig eth0:3 192.170.0.2 up
 +
oai@oai:~/openairinterface5g/cmake_targets/lte_build_oai/build$ sudo ifconfig eth0:4 192.170.1.2 up
 +
oai@oai:~/openairinterface5g/cmake_targets/lte_build_oai/build$ sudo ./lte-softmodem -E -O ~/enb.band7.tm1.50PRB.usrpb210.conf -d
 +
 +
Mark1 : Once you checkout the branch (means modify the code), you need to compile again.
 +
 +
oai@oai:~/openairinterface5g/cmake_targets$ sudo ./build_oai -w USRP -x -c --eNB
 +
 +
Mark2 : If you want to go back master from other branch, you need to send git checkout -f first and then git branch master
 +
 +
Mark3 : If you change the IP adress and then eNB part should:
 +
 +
oai@oai:~/openairinterface5g/cmake_targets/lte_build_oai/build$ sudo ifconfig eth0:3 192.170.0.2 up
 +
oai@oai:~/openairinterface5g/cmake_targets/lte_build_oai/build$ sudo ifconfig eth0:4 192.170.1.2 up
 +
oai@oai:~/openairinterface5g/cmake_targets/lte_build_oai/build$ sudo ./lte-softmodem -E -O ~/enb.band7.tm1.50PRB.usrpb210.conf -d (#run eNB)
 +
 +
Mark4 : CTRL+C to cease
 +
 +
    Connection scenario :
 +
 +
4. Testing results
 +
 +
    UE connection testing
 +
  
  

Revision as of 11:42, 30 September 2022

Sumber: https://hackmd.io/@ChiehChun/SkKj1oRoV/https%3A%2F%2Fhackmd.io%2F%40ChiehChun%2FrJkKmWPlH?type=book 



   Build OAI LTE eNB & EPC BMW Lab.@NTUST
       OAI architecture
       Build OAI LTE on VM
       OAI LTE Testing
           1. Installation on PC
           2. Set up OAI eNB and EPC
           3. RUN OAI
           4. Testing results

OAI architecture

Build OAI LTE on VM

Follow this note for building on the virtual machine OAI LTE Testing 1. Installation on PC 

   Install os

   STEP1: Format USB
   STEP2: Make a bootable USB (Refus)(https://rufus.akeo.ie/)
       Download Rufus 3.1 Portable
       Download ubuntu 14.04.5 .iso
       Open Refus and load ubuntu.iso -> click “START”
   STEP3:
   Insert USB in mini pc and press F2 to enter Bios (Depends on different computer brands)
   STEP4: Move USB to first boot order , and save(F10)
   STEP5: Install ubuntu os


name : oai password : linux 

   Internet setting

   STEP1: Check internet state

oai@oai:~$ ifconfig


Have no internet connection 

   STEP2: Editing wired connection

   Select IPV4 Settings
   Method : Manual

   Address : 140.118.121.32
   Netmask : 255.255.255.0
   Gateway : 140.118.121.254
   DNS : 140.118.31.99
   STEP3: oai@oai:~$ ifconfig , check whether connect to internet

2. Set up OAI eNB and EPC 

   OAI environment set up and installation

   STEP 1 : Environment/low-latency kernel set up

oai@oai:~$ sudo apt-get update oai@oai:~$ sudo apt-get install vim oai@oai:~$ sudo vim /etc/hosts (replace ubuntu to oai.openair4G.eur oai) oai@oai:~$ sudo reboot oai@oai:~$ sudo apt-get install git -y (#install git) oai@oai:~$ git clone https://gitlab.eurecom.fr/oai/openairinterface5g.git (# clone the eNB/UE source code) oai@oai:~$ git clone https://gitlab.eurecom.fr/oai/openair-cn.git (# clone the EPC source code)

  1. if the openair-cn can not clone from Gitlab, try the follow command

oai@oai:~$ git clone https://github.com/OPENAIRINTERFACE/openair-cn.git

oai@oai:~$ cd openair-cn/ oai@oai:~/openair-cn$ git checkout v0.3.2 (# swtich the branch to the one that we gonna use) oai@oai:~$ sudo apt-get install linux-lowlatency-lts-vivid -y (# Install low-lentency kernel) oai@oai:~$ sudo apt-get install cpufrequtils (# Set cpu scaling) oai@oai:~$ sudo vim /etc/default/cpufrequtils add GOVERNOR="performance" to this file oai@oai:~$ sudo update-rc.d ondemand disable oai@oai:~$ dpkg --get-selections | grep linux-image (# remove the kernel we won't used) oai@oai:~$ sudo apt-get purge linux-image-4.4.0-31-generic linux-image-extra-4.4.0-31-generic linux-image-generic-lts-xenial oai@oai:~$ sudo update-grub2 

   STEP 2 : Reboot and change the kernel to low-latency

@oai:~$sudo reboot

Press esc to setting interface when reboot

Change kernel 

   STEP 3 : check uname -a , you will have

   Openair-CN (EPC) installation

   STEP 1 : Build the package for HSS

oai@oai:~$ cd openair-cn/SCRIPTS/ oai@oai:~/openair-cn/SCRIPTS$ sudo ./build_hss -i (# Install the package which is needed from HSS) 

   Set MySQL password to “linux”
   Choose apache
   Set phpmyadmin password to “linux”

   STEP 2 : Build the package for EPC ( including MME and SPGW )

oai@oai:~/openair-cn/SCRIPTS$ sudo ./build_epc -i (# Install the package which is needed from epc (including MME and SPGW)) 

   Openairinterface eNB installation

   STEP 1 : Install the package which is needed from eNB, including UHD driver

oai@oai:~/openair-cn/SCRIPTS$ cd ~/openairinterface5g/cmake_targets/ oai@oai:~/openairinterface5g/cmake_targets$ sudo ./build_oai -I --eNB -x --install-system-files -w USRP 

   STEP 2 : Adapt your modification,if you do any modification related to source code

oai@oai:~/openairinterface5g/cmake_targets$ sudo ./build_oai -w USRP -x -c --eNB 

   Configuration Setting for connect eNB to EPC

eNB part- 

   STEP 1 : Copy the configruation files we will use for eNB

oai@oai:~/openairinterface5g/cmake_targets$ cd ~/openairinterface5g/targets/PROJECTS/GENERIC-LTE-EPC/CONF/ oai@oai:~/openairinterface5g/targets/PROJECTS/GENERIC-LTE-EPC/CONF$ cp enb.band7.tm1.50PRB.usrpb210.conf ~/ oai@oai:~/openairinterface5g/targets/PROJECTS/GENERIC-LTE-EPC/CONF$ cd oai@oai:~$ vim enb.band7.tm1.50PRB.usrpb210.conf

-> modify eNB configuration 

   STEP 2 : Edit configuration
   If git brach is on v0.6.1_tdd, there do NOT have “ENB_IPv4_ADDRESS_FOR_X2C” and “ENB_PORT_FOR_X2C”. And on the branch of v0.6.1_tdd, we do not set the X2C interface. However, the git branch is on the develop/master, there would have “ENB_IPv4_ADDRESS_FOR_X2C” and “ENB_PORT_FOR_X2C” in the NETWORK_INTERFACES.
   And we need to set the X2C address as same as S1U.

       : wq to save
   STEP 3: Record your eth0 ip address

oai@oai:~$ ifconfig

EPC part- (gedit epc.cong.in) 

   STEP 4 : Edit EPC configuration

   OAI config format

3. RUN OAI 

   step 1 : build epc (Terminal 1)

oai@oai:~/openair-cn/BUILD/EPC$ cd ~/openair-cn/SCRIPTS/ oai@oai:~/openair-cn/SCRIPTS$ sudo ./build_epc -i oai@oai:~/openair-cn/SCRIPTS$ sudo ./build_epc -c -l 

   step 2 : build hss (Terminal 2)

oai@oai:~/openair-cn/SCRIPTS$ sudo ./build_hss -c -l 

   STEP 3 : run epc (Terminal 1)

oai@oai:~/openair-cn/SCRIPTS$ sudo ./run_epc -i -r 

   STEP 4 : run hss (Terminal 2)

oai@oai:~/openair-cn/SCRIPTS$ sudo ./run_hss 

   STEP 5 : run eNB (Terminal 3)
   Mark : Run eNB twice to succeed

oai@oai:~$ cd openairinterface5g/cmake_targets/lte_build_oai/build/ oai@oai:~/openairinterface5g/cmake_targets/lte_build_oai/build$ sudo ifconfig eth0:3 192.170.0.2 up oai@oai:~/openairinterface5g/cmake_targets/lte_build_oai/build$ sudo ifconfig eth0:4 192.170.1.2 up oai@oai:~/openairinterface5g/cmake_targets/lte_build_oai/build$ sudo ./lte-softmodem -E -O ~/enb.band7.tm1.50PRB.usrpb210.conf -d

Mark1 : Once you checkout the branch (means modify the code), you need to compile again.

oai@oai:~/openairinterface5g/cmake_targets$ sudo ./build_oai -w USRP -x -c --eNB

Mark2 : If you want to go back master from other branch, you need to send git checkout -f first and then git branch master

Mark3 : If you change the IP adress and then eNB part should:

oai@oai:~/openairinterface5g/cmake_targets/lte_build_oai/build$ sudo ifconfig eth0:3 192.170.0.2 up oai@oai:~/openairinterface5g/cmake_targets/lte_build_oai/build$ sudo ifconfig eth0:4 192.170.1.2 up oai@oai:~/openairinterface5g/cmake_targets/lte_build_oai/build$ sudo ./lte-softmodem -E -O ~/enb.band7.tm1.50PRB.usrpb210.conf -d (#run eNB)

Mark4 : CTRL+C to cease 

   Connection scenario :

4. Testing results 

   UE connection testing



Referensi

Retrieved from "https://onnocenter.or.id/wiki/index.php?title=4G:_OpenAirInterface_instalasi&oldid=66105"