WSPR: pakai raspberrypi dan RTL2832U
sumber: http://wsprnet.org/drupal/node/6215
Langkah yang perlu di lakukan
- Raspberri pi dengan Rasbian
- RTL-SDR Dongles (RTL2832U)
Install aplikasi
sudo su sudo apt -y install build-essential cmake libfftw3-dev libusb-1.0-0-dev curl libcurl4-gnutls-dev ntp ntpdate git
Install librtlsdr
Sumber: https://github.com/steve-m/librtls
cd /usr/local/src git clone https://github.com/steve-m/librtlsdr cd /usr/local/src/librtlsdr mkdir build cd build cmake ../ make sudo make install sudo ldconfig
Install rtlsdr-wsprd
Sumber: https://github.com/Guenael/rtlsdr-wsprd
cd /usr/local/src git clone https://github.com/Guenael/rtlsdr-wsprd cd /usr/local/src/rtlsdr-wsprd make
Setup ntp
crontab -e
*/15 * * * * /usr/sbin/ntpdate id.pool.ntp.org
Run
cd /usr/local/src/rtlsdr_wsprd ./rtlsdr_wsprd
Use: rtlsdr_wsprd -f frequency -c callsign -l locator [options] -f dial frequency [(,k,M) Hz], check http://wsprnet.org/ for freq. -c your callsign (12 chars max) -l your locator grid (6 chars max) Receiver extra options: -g gain [0-49] (default: 29) -a auto gain (default: off) -o frequency offset (default: 0) -p crystal correction factor (ppm) (default: 0) -u upconverter (default: 0, example: 125M) -d direct dampling [0,1,2] (default: 0, 1 for I input, 2 for Q input) -n max iterations (default: 0 = infinite loop) -i device index (in case of multiple receivers, default: 0) Decoder extra options: -H use the hash table (could caught signal 11 on RPi) -Q quick mode, doesn't dig deep for weak signals -S single pass mode, no subtraction (same as original wsprd)
Contoh
cd /usr/local/src/rtlsdr_wsprd
./rtlsdr_wsprd -f 144.489M -c A1XYZ -l AB12cd -g 29 -o -4200 ./rtlsdr_wsprd -f 50.293M -c VE2VAX -l FN35JO -a 1 -p 45 ./rtlsdr_wsprd -f 50.293M -c VE2VAX -l FN35JO -a 1 -p 45
./rtlsdr_wsprd -f 3.5926M -c YC0MLC -l OI33KT ./rtlsdr_wsprd -f 7.0386M -c YC0MLC -l OI33KT ./rtlsdr_wsprd -f 10.1387M -c YC0MLC -l OI33KT ./rtlsdr_wsprd -f 14.0956M -c YC0MLC -l OI33KT ./rtlsdr_wsprd -f 18.1046M -c YC0MLC -l OI33KT ./rtlsdr_wsprd -f 21.0946M -c YC0MLC -l OI33KT
Freq WSPR
0.136 0.4742 1.8366 3.5926 5.2872 7.0386 10.1387 14.0956 18.1046 21.0946 24.9246 28.1246 50.293 70.091 144.489 432.300 1296.500
Beberapa Masalah
- Gunakan ferrite bead kurangi interference
- Matikan layar kurangi QRN
- Buang model yang tidak digunakan
/opt/vc/bin/tvservice -o - Remove unused modules Edit /etc/modules: #snd-bcm2835)
- Problem USB Port
Rasberian to use with a Raspberry PI I noticed some disconnection problems with USB port while using Raspbian Jessie (2016-05-27-raspbian-jessie-lite.img). I rollbacked to Raspbian Wheezy (2015-02-16-raspbian-wheezy.img) and the problems solved by themself magically... For now, I have not investigated this issue, but if you experience some "Caught signal 11" error message, it could be this same problem. For now, I would recommend Raspbian Wheezy v2015-02-16.