Free5GC: Install

From OnnoWiki
Revision as of 11:25, 9 December 2022 by Onnowpurbo (talk | contribs)
Jump to navigation Jump to search

Sumber: https://www.free5gc.org/installations/stage-1-all-in-one/


free5GC Installation on KVM Minimum Requirement Software 

OS: Ubuntu 18.04
Linux kernel: 4.15.0-43-generic
gcc 7.3.0
Go 1.11.4
QEMU emulator 2.11.1

Hardware 

CPU: Intel i5 processor
RAM: 4GB
Hard drive: 160G
NIC card: 1Gbps ethernet card

Hardware recommended 

CPU: Intel i7 processor
RAM: 8GB
Hard drive: 160G
NIC card: 10Gbps ethernet card

Hardware Tested

eNB 

WNC OSQ4G-01E2, 3GPP Rel-13 compliance (4G LTE Small Cell）
D-Link DWR-1012, 3GPP Rel-12 compliance (4G LTE Small Cell)
GemTek WLTGFC-101, 3GPP Rel-9 compliance (4G LTE Small Cell)

UE 

LG C90 cellular phone
D-Link DWR-932C dongle via USB cable

Preparation KVM Environment Setup VM NIC Cards NIC for connecting to the Internet Network source: Virtual network - NAT Interface name in VM: ens3 (in this example) NIC for connecting to eNB: Network source: Host device <Host Interface Name> Interface name in VM: ens4 (in this example) Collect eNodeB and USIM Information

eNodeB information (in this example) 

IP Address: 192.188.2.1
Gateway:    192.188.2.2 (IP of NIC connected to eNB)
PLMN:
  MCC: 208
  MNC: 93
MME GID:  1
MME Code: 1
TAC: 1

USIM information (in this example) 

IMSI 208930000000003
K    8baf473f2f8fd09487cccbd7097c6862
OPc  8e27b6af0e692e750f32667a3b14605d

Installation Please follow the instructions from Part A ~ Part C.

Part A. Compile Source Code Prerequisites Install MongoDB 3.6.3, Golang 1.11.4. 

sudo apt-get update
sudo apt-get -y install mongodb wget git
sudo systemctl start mongodb (if '/usr/bin/mongod' is not running)
  1. Check if golang is installed
go version
  1. If not, run commands below
wget -q https://storage.googleapis.com/golang/getgo/installer_linux
chmod +x installer_linux
./installer_linux
source ~/.bash_profile
rm -f installer_linux

go get -u -v "github.com/gorilla/mux"
go get -u -v "golang.org/x/net/http2"
go get -u -v "golang.org/x/sys/unix"

To run free5GC with least privilege, TUN device permission should be a crw-rw-rw-(666). 

ls -al /dev/net/tun
crw-rw-rw- 1 root root 10, 200 Jan 14 13:09 /dev/net/tun

Write the configuration file for the TUN device. 

sudo sh -c "cat << EOF > /etc/systemd/network/99-free5gc.netdev
[NetDev]
Name=uptun
Kind=tun
EOF"

sudo systemctl enable systemd-networkd
sudo systemctl restart systemd-networkd

Check IPv6 Kernel Configuration. Although you can skip this step, we suggest that you set this up to support IPv6-enabled UE. 

sysctl -n net.ipv6.conf.uptun.disable_ipv6

(if the output is 0 and IPv6 is enabled, skip the followings) 

sudo sh -c "echo 'net.ipv6.conf.uptun.disable_ipv6=0' > /etc/sysctl.d/30-free5gc.conf"
sudo sysctl -p /etc/sysctl.d/30-free5gc.conf

You are now ready to set the IP address on TUN device. If IPv6 is disabled for TUN device, please remove Address=cafe::1/64 from below. 

sudo sh -c "cat << EOF > /etc/systemd/network/99-free5gc.network
[Match]
Name=uptun
[Network]
Address=45.45.0.1/16
Address=cafe::1/64
EOF"

sudo systemctl enable systemd-networkd
sudo systemctl restart systemd-networkd

Add the following lines into /etc/network/interfaces for network-manager service 

auto uptun
iface uptun inet static  
	address 45.45.0.1 
	netmask 255.255.0.0

iface uptun inet6 static
	pre-up modprobe ipv6 
	address cafe::1
	netmask 64

Restart uptun interface 

sudo ip a flush uptun
sudo systemctl restart networking
  1. Check if uptun is up
sudo apt-get -y install net-tools
ifconfig uptun

AMF, SMF, UPF, HSS, and PCRF Install the depedencies for building the source 

sudo apt-get -y install autoconf libtool gcc pkg-config git flex bison libsctp-dev libgnutls28-dev libgcrypt-dev libssl-dev 
libidn11-dev libmongoc-dev libbson-dev libyaml-dev

Git clone and compile 

git clone https://bitbucket.org/nctu_5g/free5gc-stage-1.git
cd free5gc-stage-1
autoreconf -iv
./configure --prefix=`pwd`/install
make -j `nproc`
make install

Part B. VM Internal Network Environment Setting [Option 1] Need to run on every boot 

sudo ifconfig ens4 192.188.2.2
sudo sh -c 'echo 1 > /proc/sys/net/ipv4/ip_forward'
sudo iptables -t nat -A POSTROUTING -o ens3 -j MASQUERADE
sudo iptables -I INPUT -i uptun -j ACCEPT

[Option 2] or configure as auto run on boot 

sudo sh -c "cat << EOF > /etc/init.d/ngc-network-setup
#!/bin/sh
### BEGIN INIT INFO
# Provides:          ngc-network-setup
# Required-Start:    networkd
# Required-Stop:     networkd
# Default-Start:     networkd
# Default-Stop:      networkd
# Short-Description:
# Description:
#
### END INIT INFO

ifconfig ens4 192.188.2.2
sh -c 'echo 1 > /proc/sys/net/ipv4/ip_forward'
iptables -t nat -A POSTROUTING -o ens3 -j MASQUERADE
iptables -I INPUT -i uptun -j ACCEPT
EOF"

sudo chmod 755 /etc/init.d/ngc-network-setup
sudo /etc/init.d/ngc-network-setup

sudo ln -s /etc/init.d/ngc-network-setup /etc/rc3.d/S99ngc-network-setup
sudo ln -s /etc/init.d/ngc-network-setup /etc/rc4.d/S99ngc-network-setup
sudo ln -s /etc/init.d/ngc-network-setup /etc/rc5.d/S99ngc-network-setup

Part C. Run Run in all-in-one mode The daemon free5gc-ngcd includes AMF, SMF, UPF, HSS, and PCRF. Thus, instead of running all 5 daemons, you can just run free5gc-ngcd in your development environment. 

./free5gc-ngcd

While running free5gc-ngcd All logs for AMF, SMF, UPF, HSS, and PCRF are written to ./install/var/log/free5gc/free5gc.log. All settings are managed in one place for ./install/etc/free5gc/free5gc.conf. You can find the log/conf path at the beginning of the running screen. You can user -f argument to specify config file to be used. Run functions separately We also provide 5GC functions running separately. 

./free5gc-upfd
./free5gc-amfd
./free5gc-smfd
./nextepc-hssd
./nextepc-pcrfd

Note: We also provide a reference for 5GC functions running in separate machines.

[Optional] Self-test We provide a program that checks whether the installation is correct. After running the wireshark, select loopback interface, and then filter s1ap || diameter || gtpv2 || gtp and run ./test/testngc. You can see the packets virtually created. 

./test/testngc -f install/etc/free5gc/test/free5gc.testngc.conf

Part D. Web User Interface Install Node.js and NPM 

sudo apt-get -y install curl
curl -sL https://deb.nodesource.com/setup_8.x | sudo -E bash -
sudo apt-get -y install nodejs

Install the dependencies to run WebUI (first time) 

cd webui
npm install

Run WebUI 

cd webui
npm run dev

Now the web server is running on http://localhost:3000. The default username and password are “admin” and “1423”.

Core Network Configuration free5GC configuration file Modify ./install/etc/free5gc/free5gc.conf

amf-slap address (line 67) 

amf:
  s1ap:
    addr: <IP of GW NIC to eNB: 192.188.2.2>

upf-gtpu address (line 162) 

smf:
  upf:
    addr: <IP of GW NIC to eNB: 192.188.2.2>

AMF GUMMEI (line 91) 

amf:
  gummei:
    plmn_id:
      mcc: <eNB MCC: 208>
            mnc: <eNB MNC: 93>
    mme_gid: <eNB MME GID: 1>
    mme_code: <eNB MME Code: 1>

AMF TAI (line 130) 

amf:
  tai:
    plmn_id:
      mcc: <eNB MCC: 208>
            mnc: <eNB MNC: 93>
        tac: <eNB TAC: 1>

Add subscriber (UE) Add a subscriber by the Web UI Run the web server: 

cd ./webui && npm run dev

Visit http://localhost:3000 

 - Username : admin
 - Password : 1423

Add a subscriber with IMSI, K, OPc 

 - Go to Subscriber Menu.
 - Click `+` Button to add a new subscriber.
 - Fill the IMSI, security context(K, OPc, AMF), and APN of the subscriber.
 - Click `SAVE` Button

This addition will take effect immediately on free5GC without restaring any daemon.

Rebuild Project To completely rebuild the project after modifying source code 

(Control-C kill free5gc-ngcd)
make maintainer-clean
rm -rf ./install
git pull
autoreconf -iv
./configure --prefix=`pwd`/install
make -j `nproc`
make install
./free5gc-ngcd

Troubleshooting Note for modifying configuration file Use space for indent. DO NOT use tab. A white space must be added between the colon and value after the item name, e.g. addr: 192.188.2.2 

./test/testngc test failure

Make sure all configuration files and environment settings are correct.

Kill testngc process which didn’t finish correctly 

killall -9 testngc

Remove test subscriber left by previous failed test (NextEPC issue #57) 

$ mongo
> use free5gc
> db.subscribers.find()  ### (Check the test subscriber)
> db.subscribers.drop()  ### Remove all subscriber
> db.subscribers.find()  ### (Check that all subscribers are empty)
./free5gc-ngcd errors

ERRR: - The certificate is expired (NextEPC issue #94) 

cd support/freeDiameter
./make_certs.sh .
cd ../..
make install

Address already in use 

$ killall -9 testngc

or 

$ killall -9 free5gc-ngcd

Rebuild failure 

config.status: error: cannot find input file: `Makefile.in' (NextEPC issue #68)
autoheader \
    && aclocal \
    && libtoolize --ltdl --copy --force \
    && automake --add-missing --copy \
    && autoconf \
    && ./configure

Appendix A: Program the SIM Card

Install packages: 

sudo apt-get install pcscd pcsc-tools libccid python-dev swig python-setuptools python-pip libpcsclite-dev
sudo pip install pycrypto

Download PySIM 

git clone git://git.osmocom.org/pysim.git

Change to pyscard folder and install 

cd <pyscard-path>
sudo /usr/bin/python setup.py build_ext install

Verify your reader is ready 

sudo pcsc_scan

Check whether your reader can read the SIM card 

cd <pysim-path>
./pySim-read.py –p 0

Program your SIM card information 

./pySim-prog.py -p 0 -x 208 -y 93 -t sysmoUSIM-SJS1 -i 208930000000003 --op=8e27b6af0e692e750f32667a3b14605d -k 8baf473f2f8fd09487cccbd7097c6862 -s 8988211000000088313 -a 23605945

You can get your SIM card from sysmocom. You also need a card reader to write your SIM card. You can get a card reader from here or equivalent device will do.

Referensi

Pranala Menarik

Retrieved from "https://onnocenter.or.id/wiki/index.php?title=Free5GC:_Install&oldid=67226"