Difference between revisions of "Arduino: Ethernet Shield"

From OnnoWiki
Jump to navigation Jump to search
(New page: Sumber: https://www.arduino.cc/en/Main/ArduinoEthernetShield Download: arduino-ethernet-shield-06-schematic.pdf, arduino-ethernet-shield-06-reference-design.zip Overview The Arduino Ethe...)
 
Line 1: Line 1:
 
Sumber: https://www.arduino.cc/en/Main/ArduinoEthernetShield
 
Sumber: https://www.arduino.cc/en/Main/ArduinoEthernetShield
  
Download: arduino-ethernet-shield-06-schematic.pdf, arduino-ethernet-shield-06-reference-design.zip
 
Overview
 
  
The Arduino Ethernet Shield connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino board, connect it to your network with an RJ45 cable (not included) and follow a few simple instructions to start controlling your world through the internet. As always with Arduino, every element of the platform – hardware, software and documentation – is freely available and open-source. This means you can learn exactly how it's made and use its design as the starting point for your own circuits. Hundreds of thousands of Arduino boards are already fueling people’s creativity all over the world, everyday. Join us now, Arduino is you!
 
  
    Requires an Arduino board (not included)
 
    Operating voltage 5V (supplied from the Arduino Board)
 
    Ethernet Controller: W5100 with internal 16K buffer
 
    Connection speed: 10/100Mb
 
    Connection with Arduino on SPI port
 
  
Description
 
  
The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100 ethernet chip (datasheet). The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.
+
==Download==
 +
* https://www.arduino.cc/en/uploads/Main/arduino-ethernet-shield-06-schematic.pdf
 +
*https://www.arduino.cc/en/uploads/Main/arduino-ethernet-shield-06-reference-design.zip
  
The most recent revision of the board exposes the 1.0 pinout on rev 3 of the Arduino UNO board.
+
==Overview==
  
The Ethernet Shield has a standard RJ-45 connection, with an integrated line transformer and Power over Ethernet enabled.
+
Arduino Ethernet Perisai menghubungkan Arduino Anda ke internet dalam hitungan menit. Hanya plug modul ini ke papan Arduino Anda, hubungkan ke jaringan Anda dengan kabel RJ45 (tidak termasuk) dan mengikuti petunjuk sederhana untuk memulai mengendalikan dunia melalui internet. Seperti biasa dengan Arduino, setiap elemen dari platform - hardware, software dan dokumentasi - tersedia secara bebas dan open source. Ini berarti Anda dapat belajar persis bagaimana itu dibuat dan menggunakan desain sebagai titik awal untuk sirkuit Anda sendiri.
  
There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with all the Arduino/Genuino boards. The on-board micro SD card reader is accessible through the SD Library. When working with this library, SS is on Pin 4. The original revision of the shield contained a full-size SD card slot; this is not supported.
+
* Membutuhkan sebuah Arduino board (tidak termasuk)
 +
* Operating voltage 5V (supplied from the Arduino Board)
 +
* Ethernet Controller: W5100 dengan internal 16K buffer
 +
* Connection speed: 10/100Mb
 +
* Connection dengan Arduino di SPI port
 +
 
 +
==Penjelasan==
 +
 
 +
Arduino Ethernet Shield memungkinkan papan Arduino untuk terhubung ke internet. Hal ini didasarkan pada ethernet chip yang Wiznet W5100 (datasheet). The Wiznet W5100 menyediakan stack jaringan (IP) mampu TCP dan UDP. Mendukung hingga empat koneksi soket simultan. Menggunakan Ethernet library untuk menulis sketch yang terhubung ke internet dengan menggunakan shield. Ethernet shield terhubung ke papan Arduino menggunakan header kawat-wrap panjang yang memperpanjang melalui Shield. Hal ini membuat tata letak pin utuh dan memungkinkan Shield lain yang ditumpuk di atas.
 +
 
 +
Revisi terbaru dari papan ekspose pinout 1.0 pada rev 3 dari papan Eduino UNO.
 +
 
 +
Ethernet Shield memiliki standar RJ-45 koneksi, dengan transformator line terpadu dan Power over Ethernet diaktifkan.
 +
 
 +
Ada slot kartu micro-SD onboard, yang dapat digunakan untuk menyimpan file untuk melayani melalui jaringan. Hal ini kompatibel dengan semua papan Arduino / Genuino. Pembaca kartu micro SD on-board dapat diakses melalui SD library. Ketika bekerja dengan library ini, SS adalah pada Pin 4. Revisi asli dari Shield yang terkandung SD ukuran full-size; ini tidak didukung lagi.The Ethernet Shield memiliki standar RJ-45 koneksi, dengan transformator terpadu dan Power over Ethernet diaktifkan.
  
 
The shield also includes a reset controller, to ensure that the W5100 Ethernet module is properly reset on power-up. Previous revisions of the shield were not compatible with the Mega and need to be manually reset after power-up.
 
The shield also includes a reset controller, to ensure that the W5100 Ethernet module is properly reset on power-up. Previous revisions of the shield were not compatible with the Mega and need to be manually reset after power-up.
Line 26: Line 33:
 
The current shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted pair Category 5 Ethernet cable:
 
The current shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted pair Category 5 Ethernet cable:
  
    IEEE802.3af compliant
+
* IEEE802.3af compliant
    Low output ripple and noise (100mVpp)
+
* Low output ripple and noise (100mVpp)
    Input voltage range 36V to 57V
+
* Input voltage range 36V to 57V
    Overload and short-circuit protection
+
* Overload and short-circuit protection
    9V Output
+
* 9V Output
    High efficiency DC/DC converter: typ 75% @ 50% load
+
* High efficiency DC/DC converter: typ 75% @ 50% load
    1500V isolation (input to output)  
+
* 1500V isolation (input to output)  
  
NB: the Power over Ethernet module is proprietary hardware not made by Arduino, it is a third party accessory. For more information, see the datasheet
+
NB: the Power over Ethernet module is proprietary hardware not made by Arduino, it is a third party accessory.
  
 
The shield does not come with the PoE module built in, it is a separate component that must be added on.
 
The shield does not come with the PoE module built in, it is a separate component that must be added on.
Line 48: Line 55:
 
The shield contains a number of informational LEDs:
 
The shield contains a number of informational LEDs:
  
    PWR: indicates that the board and shield are powered
+
* PWR: indicates that the board and shield are powered
    LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
+
* LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
    FULLD: indicates that the network connection is full duplex
+
* FULLD: indicates that the network connection is full duplex
    100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
+
* 100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
    RX: flashes when the shield receives data
+
* RX: flashes when the shield receives data
    TX: flashes when the shield sends data
+
* TX: flashes when the shield sends data
    COLL: flashes when network collisions are detected  
+
* COLL: flashes when network collisions are detected  
  
 
The solder jumper marked "INT" can be connected to allow the Arduino board to receive interrupt-driven notification of events from the W5100, but this is not supported by the Ethernet library. The jumper connects the INT pin of the W5100 to digital pin 2 of the Arduino.
 
The solder jumper marked "INT" can be connected to allow the Arduino board to receive interrupt-driven notification of events from the W5100, but this is not supported by the Ethernet library. The jumper connects the INT pin of the W5100 to digital pin 2 of the Arduino.

Revision as of 05:55, 20 November 2015

Sumber: https://www.arduino.cc/en/Main/ArduinoEthernetShield



Download

Overview

Arduino Ethernet Perisai menghubungkan Arduino Anda ke internet dalam hitungan menit. Hanya plug modul ini ke papan Arduino Anda, hubungkan ke jaringan Anda dengan kabel RJ45 (tidak termasuk) dan mengikuti petunjuk sederhana untuk memulai mengendalikan dunia melalui internet. Seperti biasa dengan Arduino, setiap elemen dari platform - hardware, software dan dokumentasi - tersedia secara bebas dan open source. Ini berarti Anda dapat belajar persis bagaimana itu dibuat dan menggunakan desain sebagai titik awal untuk sirkuit Anda sendiri.

  • Membutuhkan sebuah Arduino board (tidak termasuk)
  • Operating voltage 5V (supplied from the Arduino Board)
  • Ethernet Controller: W5100 dengan internal 16K buffer
  • Connection speed: 10/100Mb
  • Connection dengan Arduino di SPI port

Penjelasan

Arduino Ethernet Shield memungkinkan papan Arduino untuk terhubung ke internet. Hal ini didasarkan pada ethernet chip yang Wiznet W5100 (datasheet). The Wiznet W5100 menyediakan stack jaringan (IP) mampu TCP dan UDP. Mendukung hingga empat koneksi soket simultan. Menggunakan Ethernet library untuk menulis sketch yang terhubung ke internet dengan menggunakan shield. Ethernet shield terhubung ke papan Arduino menggunakan header kawat-wrap panjang yang memperpanjang melalui Shield. Hal ini membuat tata letak pin utuh dan memungkinkan Shield lain yang ditumpuk di atas.

Revisi terbaru dari papan ekspose pinout 1.0 pada rev 3 dari papan Eduino UNO.

Ethernet Shield memiliki standar RJ-45 koneksi, dengan transformator line terpadu dan Power over Ethernet diaktifkan.

Ada slot kartu micro-SD onboard, yang dapat digunakan untuk menyimpan file untuk melayani melalui jaringan. Hal ini kompatibel dengan semua papan Arduino / Genuino. Pembaca kartu micro SD on-board dapat diakses melalui SD library. Ketika bekerja dengan library ini, SS adalah pada Pin 4. Revisi asli dari Shield yang terkandung SD ukuran full-size; ini tidak didukung lagi.The Ethernet Shield memiliki standar RJ-45 koneksi, dengan transformator terpadu dan Power over Ethernet diaktifkan.

The shield also includes a reset controller, to ensure that the W5100 Ethernet module is properly reset on power-up. Previous revisions of the shield were not compatible with the Mega and need to be manually reset after power-up.

The current shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted pair Category 5 Ethernet cable:

  • IEEE802.3af compliant
  • Low output ripple and noise (100mVpp)
  • Input voltage range 36V to 57V
  • Overload and short-circuit protection
  • 9V Output
  • High efficiency DC/DC converter: typ 75% @ 50% load
  • 1500V isolation (input to output)

NB: the Power over Ethernet module is proprietary hardware not made by Arduino, it is a third party accessory.

The shield does not come with the PoE module built in, it is a separate component that must be added on.

Arduino communicates with both the W5100 and SD card using the SPI bus (through the ICSP header). This is on digital pins 10, 11, 12, and 13 on the Uno and pins 50, 51, and 52 on the Mega. On both boards, pin 10 is used to select the W5100 and pin 4 for the SD card. These pins cannot be used for general I/O. On the Mega, the hardware SS pin, 53, is not used to select either the W5100 or the SD card, but it must be kept as an output or the SPI interface won't work.

Note that because the W5100 and SD card share the SPI bus, only one can be active at a time. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W5100, set digital pin 10 as a high output.

The shield provides a standard RJ45 ethernet jack.

The reset button on the shield resets both the W5100 and the Arduino board.

The shield contains a number of informational LEDs:

  • PWR: indicates that the board and shield are powered
  • LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
  • FULLD: indicates that the network connection is full duplex
  • 100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
  • RX: flashes when the shield receives data
  • TX: flashes when the shield sends data
  • COLL: flashes when network collisions are detected

The solder jumper marked "INT" can be connected to allow the Arduino board to receive interrupt-driven notification of events from the W5100, but this is not supported by the Ethernet library. The jumper connects the INT pin of the W5100 to digital pin 2 of the Arduino.

See also: getting started with the ethernet shield and Ethernet library reference



Referensi