Dial menggunakan WvDial

Setelah WvDial di instalasi. Pastikan modem usb terdeteksi system operasi

lsusb
ls -la /dev/ttyU*

lakukan

$ wvdialconf

Akan tampak tampilan sebagai berikut

Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.

Modem Port Scan<*1>: S0   S1   S2   S3   
WvModem<*1>: Cannot get information for serial port.
ttyUSB0<*1>: ATQ0 V1 E1 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyUSB0<*1>: Modem Identifier: ATI -- Manufacturer: ZTE INCORPORATED
ttyUSB0<*1>: Speed 9600: AT -- OK
ttyUSB0<*1>: Max speed is 9600; that should be safe.
ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
WvModem<*1>: Cannot get information for serial port.
ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud
ttyUSB1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
WvModem<*1>: Cannot get information for serial port.
ttyUSB2<*1>: ATQ0 V1 E1 -- OK
ttyUSB2<*1>: ATQ0 V1 E1 Z -- OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyUSB2<*1>: Modem Identifier: ATI -- Manufacturer: ZTE INCORPORATED
ttyUSB2<*1>: Speed 9600: AT -- OK
ttyUSB2<*1>: Max speed is 9600; that should be safe.
ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK 

Found a modem on /dev/ttyUSB0.
Modem configuration written to /etc/wvdial.conf.
/etc/wvdial.conf<Warn>: Can't write '/etc/wvdial.conf.tmp4540': Permission denied
/etc/wvdial.conf<Warn>: Can't write '/etc/wvdial.conf' ('/etc/wvdial.conf'): Bad file descriptor
ttyUSB0<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
ttyUSB2<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"

Edit wvdial.conf

sudo vi /etc/wvdial.conf 

Tambahkan misalnya

[Dialer xl3g]
Phone = *99***1#
Username = xlgprs
Password = proxl
Stupid Mode = 1
Dial Command = ATDT
Modem = /dev/ttyUSB0
Baud = 460800
Init2 = ATZ
Init3 = ATE0V1&D2&C1S0=0+IFC=2,2
ISDN = 0
Modem Type = Analog Modem
Init5 =AT+CGDCONT=1,"IP","www.xlgprs.net";

Dial menggunakan

$ wvdial xl3g

Pranala Menarik

• Instalasi USB mode switch untuk USB Modem yang ada Storage
• Instalasi WvDial
• Dial menggunakan Modem