Difference between revisions of "OpenWRT: Flash Linksys E900"

From OnnoWiki
Jump to navigation Jump to search
(New page: Hardware Information CPU Broadcom BCM5357 CPU Speed 300 MHz Flash ROM 8 MB RAM 32 MB Radio 2.4 GHz WLAN Support b/g/n WLAN Max Speed 300 mbps Antenna Location Internal MIMO Config ...)
 
 
(2 intermediate revisions by the same user not shown)
Line 1: Line 1:
Hardware Information
+
Spesifikasi
CPU Broadcom BCM5357
 
CPU Speed 300 MHz
 
Flash ROM 8 MB
 
RAM 32 MB
 
Radio 2.4 GHz
 
WLAN Support b/g/n
 
WLAN Max Speed 300 mbps
 
Antenna Location Internal
 
MIMO Config 2 Transmit x 2 Receieve
 
Switch 4x 10/100 LAN + 1 10/100 WAN
 
USB Port None
 
  
 
+
CPU Broadcom BCM5357
[edit] Flashing instructions for the E900
+
CPU Speed 300 MHz
 +
Flash ROM 8 MB
 +
RAM 32 MB
 +
Radio 2.4 GHz
 +
WLAN Support b/g/n
 +
WLAN Max Speed 300 mbps
 +
Antenna Location Internal
 +
MIMO Config 2 Transmit x 2 Receieve
 +
Switch 4x 10/100 LAN + 1 10/100 WAN
 +
USB Port None
  
 
After using the trailed build file for the initial flash (yes the file with the router name in it) only use nv64k builds to upgrade with or you will brick your unit. Don't confuse this unit with some of the other Linksys E-Series units that use nv60k builds, this one uses nv64k builds!
 
After using the trailed build file for the initial flash (yes the file with the router name in it) only use nv64k builds to upgrade with or you will brick your unit. Don't confuse this unit with some of the other Linksys E-Series units that use nv60k builds, this one uses nv64k builds!
  
    Read the Peacock Announcement carefully.
+
* Read the Peacock Announcement carefully.
    Disconnect all cables and wireless clients.
+
* Disconnect all cables and wireless clients.
    Do a 30/30/30 reset on router
+
* Do a 30/30/30 reset on router
    Connect 1 Lan cable to pc doing the flash.
+
* Connect 1 Lan cable to pc doing the flash.
    Log into Linkysys Web Interface Firmware Upgrade page at 192.168.1.1 and flash the firmware E900 Trailed Initial Flash Build
+
* Log into Linkysys Web Interface Firmware Upgrade page at 192.168.1.1 and flash the firmware E900 Trailed Initial Flash Build
    Wait 5 minutes to assure flash integrity.
+
* Wait 5 minutes to assure flash integrity.
    Power cycle by unplugging the E900 for 10 seconds.
+
* Power cycle by unplugging the E900 for 10 seconds.
    Plug the E900 back in and wait about 2 minutes until it finishes booting.
+
* Plug the E900 back in and wait about 2 minutes until it finishes booting.
    Do a 30/30/30 reset on router. Another power cycle may be required after hard reset as noted by some forum users.
+
* Do a 30/30/30 reset on router. Another power cycle may be required after hard reset as noted by some forum users.
    Wait 3 minutes and log into web interface.
+
* Wait 3 minutes and log into web interface.
    You are done.  
+
* You are done.  
 
 
    After the initial flash - should you want to flash to a build with more features you can use a k2.6 nv64k BIG or mega build or any of the other build flavors that are of your liking for features.
 
 
 
    For upgrading to a newer build you can follow these steps: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=176523
 
 
 
ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2013/05-27-2013-r21676/broadcom_K26/dd-wrt.v24-21676_NEWD-2_K2.6_big-nv64k.bin
 
[edit] Build information
 
 
 
As noted in bold at the beginning of the flashing instructions, only use builds with nv64k in the name for upgrading - otherwise follow the initial flash instructions above if you are going from stock to dd-wrt, any other builds for upgrading an exsisting dd-wrt install without nv64k in the name will brick your router! This unit was supported with build 18946 or greater, this means you cannot use a build with a number lesser than 18946. For the safest results, use builds that are linked within this wiki as they have most likely been forum tested with ok reported results.
 
 
 
To find the latest builds, you can browse the DD-WRT file server and look for the broadcom_K26 folder, in there is the appropriate for your unit. Be aware that these are beta test builds and should be used with caution!
 
 
 
ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2
 
[edit] Reverting to stock firmware
 
 
 
It has been asked about: "how do i revert back to stock firmware?" and the answer is download the stock firmware image from the manufacturer's website, reset the router back to defaults using a 30-30-30 hard reset, then flash the stock image from within the dd-wrt webgui. After 5 minutes it should finish, you will then need to do another 30-30-30 reset and then access the stock webgui @ 192.168.1.1
 
 
 
You can also download the OEM firmware here:
 
 
 
http://www.dd-wrt.com/phpBB2/download.php?id=23644
 
[edit] Useful Links
 
 
 
Here is the link for the forum discussion thread regarding the E900:
 
  
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=152924
+
After the initial flash - should you want to flash to a build with more features you can use a k2.6 nv64k BIG or mega build or any of the other build flavors that are of your liking for features.  
  
 +
For upgrading to a newer build you can follow these steps: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=176523
  
 +
ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2013/05-27-2013-r21676/broadcom_K26/dd-wrt.v24-21676_NEWD-2_K2.6_big-nv64k.bin
  
  

Latest revision as of 14:18, 11 January 2015

Spesifikasi

CPU 	Broadcom BCM5357
CPU Speed 	300 MHz
Flash ROM 	8 MB
RAM 	32 MB
Radio 	2.4 GHz
WLAN Support 	b/g/n
WLAN Max Speed 	300 mbps
Antenna Location 	Internal
MIMO Config 	2 Transmit x 2 Receieve
Switch 	4x 10/100 LAN + 1 10/100 WAN
USB Port 	None

After using the trailed build file for the initial flash (yes the file with the router name in it) only use nv64k builds to upgrade with or you will brick your unit. Don't confuse this unit with some of the other Linksys E-Series units that use nv60k builds, this one uses nv64k builds!

  • Read the Peacock Announcement carefully.
  • Disconnect all cables and wireless clients.
  • Do a 30/30/30 reset on router
  • Connect 1 Lan cable to pc doing the flash.
  • Log into Linkysys Web Interface Firmware Upgrade page at 192.168.1.1 and flash the firmware E900 Trailed Initial Flash Build
  • Wait 5 minutes to assure flash integrity.
  • Power cycle by unplugging the E900 for 10 seconds.
  • Plug the E900 back in and wait about 2 minutes until it finishes booting.
  • Do a 30/30/30 reset on router. Another power cycle may be required after hard reset as noted by some forum users.
  • Wait 3 minutes and log into web interface.
  • You are done.

After the initial flash - should you want to flash to a build with more features you can use a k2.6 nv64k BIG or mega build or any of the other build flavors that are of your liking for features.

For upgrading to a newer build you can follow these steps: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=176523

ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2013/05-27-2013-r21676/broadcom_K26/dd-wrt.v24-21676_NEWD-2_K2.6_big-nv64k.bin 


Referensi