Difference between revisions of "OpenWRT: quagga olsr"
Onnowpurbo (talk | contribs) (Created page with "sumber: http://olsrdq.sourceforge.net/ 1. Overview The pro-active routing protocol Optimized Link State Routing (described in RFC 3626) is an optimization of the classical...") |
Onnowpurbo (talk | contribs) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 1: | Line 1: | ||
sumber: http://olsrdq.sourceforge.net/ | sumber: http://olsrdq.sourceforge.net/ | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
$ telnet localhost 2611 | $ telnet localhost 2611 | ||
| Line 69: | Line 17: | ||
5. Commands | 5. Commands | ||
The common commands for Quagga daemons work in OLSRd as well. You can use show running-config and write file to display current configuration and to write the configuration to disk. For more `basic Quagga commands' please visit http://www.quagga.net/docs/docs-multi/Basic-commands.html. In the next subsections you will find a summary of OLSRd specific commads. | The common commands for Quagga daemons work in OLSRd as well. You can use show running-config and write file to display current configuration and to write the configuration to disk. For more `basic Quagga commands' please visit http://www.quagga.net/docs/docs-multi/Basic-commands.html. In the next subsections you will find a summary of OLSRd specific commads. | ||
| + | |||
5.1. Show OLSR Information | 5.1. Show OLSR Information | ||
| Line 232: | Line 181: | ||
* http://olsrdq.sourceforge.net/ | * http://olsrdq.sourceforge.net/ | ||
| + | |||
| + | |||
| + | ==Pranala Menarik== | ||
| + | |||
| + | * [[OpenWRT]] | ||
Latest revision as of 11:23, 18 November 2018
sumber: http://olsrdq.sourceforge.net/
$ telnet localhost 2611 Trying 127.0.0.1... Connected to localhost.localdomain. Escape character is '^]'.
Hello, this is Quagga (version 0.98.5). Copyright 1996-2005 Kunihiro Ishiguro, et al.
User Access Verification
Password: olrsd>
5. Commands The common commands for Quagga daemons work in OLSRd as well. You can use show running-config and write file to display current configuration and to write the configuration to disk. For more `basic Quagga commands' please visit http://www.quagga.net/docs/docs-multi/Basic-commands.html. In the next subsections you will find a summary of OLSRd specific commads.
5.1. Show OLSR Information
Command: show ip olsr
The command displays current OLSR status. Node willingness, neighbor hold time, the time to `remember' packets to avoid duplicate forwarding, the time to `remember' topology control messages if they are not refreshed and the delaying times for MPR and routing table refreshes.
olrsd# show ip olsr OLSR Routing Process, Main Address: 172.16.56.1 Willingness: default Neighbor hold time: 6.000 s Duplicate hold time: 30.000 s Topology hold time: 15.000 s MPR update time: 1.000 s Routing table update time: 2.000 s
Command: show ip olsr linkset
The command will print the connected links (symetric or asymmetric) of this node.
Command: show ip olsr neigh
The command will print the symetric neighbors of this node together with their status (MPR of this router or MPR Selector of this router).
olrsd# show ip olsr neighbor MAIN ADDR STATUS WILLINGNGESS MPR MPRS 172.16.56.132 sym default Yes Nope 172.16.56.128 not low Nope Nope 172.16.56.130 sym default Nope Nope
Command: show ip olsr mid
The command will print the Multiple Information Association database. See RFC3626 for details.
Command: show ip olsr topset
The command will print the Topology informations that this router had gathered.
Command: show ip olsr routes
The command will print the routes discovered by OLSR.
olrsd# show ip olsr routes Dest addr Next hop Dist Iface 172.16.56.1 172.16.56.128 3 172.16.56.1 172.16.56.128 172.16.56.128 1 172.16.56.1 172.16.56.132 172.16.56.132 1 172.16.56.1 192.168.0.1 172.16.56.128 1 172.16.56.1 192.168.0.2 172.16.56.132 1 172.16.56.1 192.168.0.4 172.16.56.128 2 172.16.56.1 192.168.0.5 172.16.56.128 2 172.16.56.1
5.2. OLSR router
Command: router olsr
Enable OLSR routing process. The command is available from the `configure' node. In the `router olsr' node, the following commands are available:
Command: olsr willingness (never|low|default|high|always) Command: olsr willingness <0-7> Command: no olsr willingness
These commands are used to set the node's willingness which is a number between 0 and 7. A node with willingness `never' will never be selected as MPR. A node with willingness `always' will always be selected as MPR. The `no olsr willingness' command sets the willingness to default.
Command: olsr neighb-hold-time msecs Command: no olsr neighb-hold-time Command: olsr dup-hold-time msecs Command: no olsr dup-hold-time Command: olsr top-hold-time msecs Command: no olsr top-hold-time
These commands set the holding times for various tuples (neighbors, packets for identifying duplicates and topology infos) from implementations as suggested in RFC. The commands starting with `no' reset the parameters to their default values.
Command: olsr mpr-update-time msecs Command: no olsr mpr-update-time Command: olsr rt-update-time msecs Command: no olsr rt-update-time
Because MPR and route calculations are rather complex computations and because one topology change is usually followed by others in a short period of time, you have the option to delay the computations with a specified time after the first change was discovered. Setting big values to these fields will reduce computations while setting small values (or zero) will improve reactivity. The routing table delay time should be greater than MPR delay time as routing calculations depend on the MPR set. 5.3. OLSR interfaces
There are some OLSR interface specific options. To access interface options use interface label in the `config' mode.
Command: ip olsr hello-interval msecs Command: no ip olsr hello-interval msecs Command: ip olsr mid-interval msecs Command: no ip olsr mid-interval msecs Command: ip olsr tc-interval msecs Command: no ip olsr tc-interval msecs
These commands set the generation times for the three types of messages currently supported: hello messages, topology control messages and multiple interface associations messages. The `no' versions restore the defaults. 5.3. OLSR Debugging
Command: debug olsr packet (hello|mid|tc|all) Command: no debug olsr packet (hello|mid|tc|all)
Enables/Disables logging for received packets of specified type.
Command: debug olsr event zebra Command: no debug olsr event zebra
Enables/Disables logging for received messages from the zebra daemon.
Command: debug olsr event route-table Command: no debug olsr event route-table
Enables/Disables logging for route table changes.
Command: debug olsr event neigh Command: no debug olsr event neigh
Enables/Disables logging for the 1-hop neighborhood changes.
Command: debug olsr event links Command: no debug olsr event links
Enables/Disables logging for adjacent links changes. 6. Sample session
Here is the start of a simple sample session with OLSRd:
$ zebra -d $ olsrd -d $ telnet localhost 2611 Trying 127.0.0.1... Connected to localhost.localdomain. Escape character is '^]'.
Hello, this is Quagga (version 0.98.5). Copyright 1996-2005 Kunihiro Ishiguro, et al.
User Access Verification
Password: olrsd> show ip olsr neighbor MAIN ADDR STATUS WILLINGNGESS MPR MPRS 172.16.56.135 sym default Nope Nope
olrsd> enable
olrsd# configure terminal
olrsd(config)# router olsr
olrsd(config-router)# network
A.B.C.D/M OLSR network prefix
olrsd(config-router)# network 192.168.54.1/24
olrsd(config-router)# show ip olsr
OLSR Routing Process, Main Address: 172.16.56.1
Willingness: default
Neighbor hold time: 40.000 s
Duplicate hold time: 30.000 s
Topology hold time: 15.000 s
MPR update time: 1.000 s
Routing table update time: 2.000 s
olrsd(config-router)#
7. Credits
At this point, Tudor Golubenco is the only developer of this project. If you are a programmer and want to contribuite or if you have questions regarding this project, please contact me at tudor a.t golubenco.org.
Referensi