Difference between revisions of "UBNT: openwrt"
Jump to navigation
Jump to search
Onnowpurbo (talk | contribs) |
Onnowpurbo (talk | contribs) |
||
| Line 17: | Line 17: | ||
==Flash Update== | ==Flash Update== | ||
| − | |||
| − | + | ||
| − | + | * Set IP PC 192.168.1.x | |
| − | + | * Matikan Device UBNT | |
| − | + | * Tekan tombol Reset | |
| − | + | * Nyalakan Device UBNT | |
| − | + | * Lepaskan tombol Reset setelah ~10 detik (tidak lebih) sesudah device UBNT di nyalakan. Kita akan mengetahui-nya karena LED akan berubah. | |
| + | * Ping 192.168.1.20. Jika ada responds, kita siap untuk meng-upload image. Jika tidak maka mulai lagi dari awal. | ||
| + | * tftp image menggunakan mode binary ke 192.168.1.20 sebagai 'flash_update'. | ||
| + | |||
| + | tftp 192.168.1.20 | ||
| + | tftp> binary | ||
| + | tftp> trace | ||
| + | tftp> put flash_update | ||
| + | |||
Configuring IP addressl | Configuring IP addressl | ||
Once you finish these steps your device will have the OpenWRT firmware loaded. Then point your web browser at 192.168.1.1 and proceed by setting a password for the root (administrative) account. | Once you finish these steps your device will have the OpenWRT firmware loaded. Then point your web browser at 192.168.1.1 and proceed by setting a password for the root (administrative) account. | ||
| − | |||
==Prosedur Recovery Firmware== | ==Prosedur Recovery Firmware== | ||
Revision as of 09:42, 21 July 2012
Sumber: http://wiki.ubnt.com/Installing_OpenWRT_on_NanoStations/Bullets
Berikut adalah prosedur untuk mem-flash Ubiquiti Bullet 2 atau Nano2/Loco2. Prosedur ini akan mengganti AirOS firmware dengan OpenWRT firmware.
WARNING: penggunaan firmware ini akan men-disable beberapa fungsi device, seperti LED dan Ubiquiti Web interface. Kita dapat mengembalikannya melalui “Recovery of Ubiquiti firmware”
Download OpenWRT
Download OpenWRT firmware untuk Ubiquiti dari
http://downloads.openwrt.org/snapshots/trunk/atheros/ Nano2 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt2-squashfs.bin Pico2 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt2-pico2-squashfs.bin Nano5 http://downloads.openwrt.org/snapshots/trunk/atheros/openwrt-atheros-ubnt5-squashfs.bin
Flash Update
- Set IP PC 192.168.1.x
- Matikan Device UBNT
- Tekan tombol Reset
- Nyalakan Device UBNT
- Lepaskan tombol Reset setelah ~10 detik (tidak lebih) sesudah device UBNT di nyalakan. Kita akan mengetahui-nya karena LED akan berubah.
- Ping 192.168.1.20. Jika ada responds, kita siap untuk meng-upload image. Jika tidak maka mulai lagi dari awal.
- tftp image menggunakan mode binary ke 192.168.1.20 sebagai 'flash_update'.
tftp 192.168.1.20 tftp> binary tftp> trace tftp> put flash_update
Configuring IP addressl
Once you finish these steps your device will have the OpenWRT firmware loaded. Then point your web browser at 192.168.1.1 and proceed by setting a password for the root (administrative) account.
Prosedur Recovery Firmware
Referensi
- http://wiki.ubnt.com/Installing_OpenWRT_on_NanoStations/Bullets
- http://wiki.openwrt.org/toh/ubiquiti/nanostation
- http://downloads.openwrt.org/snapshots/trunk/atheros/