VoIP Cookbook: Linksys Wireless-G IP Phone - Revision history

Onnowpurbo at 22:54, 13 May 2010

2010-05-13T22:54:17Z

Onnowpurbo at 07:49, 8 March 2010

2010-03-08T07:49:07Z

Onnowpurbo: New page: Linksys launched a Wireless-G IP Phone a dedicated WiFi Phone. It is not a PDA nor ordinary cellphone (See figure 3.12). If you have the WiFi Phone properly configured, connected to the Wi...

2010-03-08T07:02:56Z

New page: Linksys launched a Wireless-G IP Phone a dedicated WiFi Phone. It is not a PDA nor ordinary cellphone (See figure 3.12). If you have the WiFi Phone properly configured, connected to the Wi...

New page

Linksys launched a Wireless-G IP Phone a dedicated WiFi Phone. It is not a PDA nor ordinary cellphone (See figure 3.12). If you have the WiFi Phone properly configured, connected to the Wireless Access Point and registered to a VoIP Softswitch, then what should appear on the screen of the phone is the name of the access point and the telephone number of the phone. Under this circumstance, the WiFi Phone is ready to be used for calling.

[[Image:Wifiphone01.jpg|center|200px|thumb|Wireless-G IP Phone]]

[[Image:Wifiphone02.jpg|center|200px|thumb|WiFi Phone can be used for VoIP call when it is properly configured]]

In Linksys WiFi Phone main menu, there are at least two (2) things you have to configure so that your phone will function well. Firstly, the wireless settings, by which we can scan any access point wireless frequency and connect our phone to the access point so we can be connected to the internet. Secondtly, the Phone Settings, allows us to configure the SIP server that we use to call. For the latter, you need to fill in the information pertaining to phone numbers, passwords and the servers used. Since we are using VoIP Rakyat as an example, the information should be those of VoIP Rakyat.

[[Image:Wifiphone03.jpg|center|200px|thumb|Through the phone menu, you can make direct configuration in order to make your phone VoIP enabled]]

Configuring the WiFi Phone using menu shown in the figure is easy, but since there is no software that could help us capture the screens for configuring the phone, we use the web configuration instead for the purpose of helping you understand how to configure the WiFi Phone. The same result should otherwise be similar to that of direct phone configuration. In contrast to WiFi Phone that is combined with PDA or GSM, Linksys WiFi Phone can be configured using the web, in addition to feature allowing you to directly make configuration using the menu available in the phone screen.

==See Also==

* [[VoIP Cookbook: Building your own Telecommunication Infrastructure]]
* [[VoIP Cookbook: VoIP Hardware for experienced Users]]

@@ Line 18: / Line 18: @@
 you can set how you will obtain your IP address]]
-Once you have entered the username and password, you will be brought to the administration panel whereby you can configure the IP address. Normally, in a hotspot that provides any user connecting to it with free IP address, we just need to set the configuration to “Automatic Configuration-DHCP”. In the case where the IP address is not provided automatically by the hotspot, you have to manually enter the information pertaining to the IP address, subnet mask, gateway, primary and secondary DNS. The MAC address of the WiFi Phone appears by default. Once you have finished entering these information, click Save Settings to save them into the memory.
+Once you have entered the username and password, you will be brought to the administration panel whereby you can configure the [[IP address]]. Normally, in a [[hotspot]] that provides any user connecting to it with free [[IP address]], we just need to set the configuration to “Automatic Configuration-DHCP”. In the case where the [[IP address]] is not provided automatically by the hotspot, you have to manually enter the information pertaining to the [[IP address]], subnet mask, gateway, primary and secondary DNS. The MAC address of the WiFi Phone appears by default. Once you have finished entering these information, click Save Settings to save them into the memory.
 [[Image:Wifiphone06.jpg|center|200px|thumb|By clicking on the Phonebook menu,
@@ Line 27: / Line 27: @@
 [[Image:Wifiphone07.jpg|center|200px|thumb|SIP Settings]]
-In the SIP Settings tab, we can configure the IP address of the SIP Proxy, SIP Port (usually 5060), the IP address of the SIP Registrar (usually the same as that of SIP Proxy), Registrar Port (also usually 5060), and SIP account number consisting of telephone number and the password related. As for VoIP Rakyat SIP information, fill in the SIP Proxy and SIP Registrar with voiprakyat.or.id.
+In the SIP Settings tab, we can configure the [[IP address]] of the [[SIP Proxy]], SIP Port (usually 5060), the [[IP address]] of the [[SIP]] Registrar (usually the same as that of [[SIP Proxy]]), Registrar Port (also usually 5060), and [[SIP]] account number consisting of telephone number and the password related. As for [[VoIP Rakyat]] [[SIP]] information, fill in the [[SIP Proxy]] and [[SIP Registrar]] with voiprakyat.or.id.
 [[Image:Wifiphone08.jpg|center|200px|thumb|NAT Settings]]
-In the NAT Settings menu, you can configure the Proxy address and Proxy Port. The Proxy address for VoIP Rakyat is voiprakyat.or.id. And the Proxy Port normally used is 5060.
+In the [[NAT]] Settings menu, you can configure the Proxy address and Proxy Port. The Proxy address for [[VoIP Rakyat]] is voiprakyat.or.id. And the Proxy Port normally used is 5060.
 [[Image:Wifiphone09.jpg|center|200px|thumb|The SIP-SDP Settings tab]]
-In SIP-SDP Settings tab, we can configure several things related to the type of Codec, packet time, DTMF Relay, UDP Port and RTP Port. These parameters are good by default, so just leave them as is.
+In SIP-SDP Settings tab, we can configure several things related to the type of [[Codec]], packet time, [[DTMF]] Relay, [[UDP Port]] and [[RTP Port]]. These parameters are good by default, so just leave them as is.
 [[Image:Wifiphone10.jpg|center|200px|thumb|By clicking on the wireless tab of the administration panel, you can find out to which hotspot the phone is connected]]
@@ Line 49: / Line 49: @@
 * [[VoIP Cookbook: Building your own Telecommunication Infrastructure]]
 * [[VoIP Cookbook: VoIP Hardware for experienced Users]]

← Older revision		Revision as of 07:49, 8 March 2010
Line 11:		Line 11:
	Configuring the WiFi Phone using menu shown in the figure is easy, but since there is no software that could help us capture the screens for configuring the phone, we use the web configuration instead for the purpose of helping you understand how to configure the WiFi Phone. The same result should otherwise be similar to that of direct phone configuration. In contrast to WiFi Phone that is combined with PDA or GSM, Linksys WiFi Phone can be configured using the web, in addition to feature allowing you to directly make configuration using the menu available in the phone screen.		Configuring the WiFi Phone using menu shown in the figure is easy, but since there is no software that could help us capture the screens for configuring the phone, we use the web configuration instead for the purpose of helping you understand how to configure the WiFi Phone. The same result should otherwise be similar to that of direct phone configuration. In contrast to WiFi Phone that is combined with PDA or GSM, Linksys WiFi Phone can be configured using the web, in addition to feature allowing you to directly make configuration using the menu available in the phone screen.

		+	[[Image:Wifiphone04.jpg\|center\|200px\|thumb\|Enter the user name and password to log in the administration panel so that you can configure the phone]]

		+	The web will appear as what is shown as figure 3.15. It is the display prompting you to enter your user name and the password required to authenticate your account. The default for the username and password is admin and admin respectively.

		+	[[Image:Wifiphone05.jpg\|center\|200px\|thumb\|Through the Network Tab of the administration panel,
		+	you can set how you will obtain your IP address]]

		+	Once you have entered the username and password, you will be brought to the administration panel whereby you can configure the IP address. Normally, in a hotspot that provides any user connecting to it with free IP address, we just need to set the configuration to “Automatic Configuration-DHCP”. In the case where the IP address is not provided automatically by the hotspot, you have to manually enter the information pertaining to the IP address, subnet mask, gateway, primary and secondary DNS. The MAC address of the WiFi Phone appears by default. Once you have finished entering these information, click Save Settings to save them into the memory.

		+	[[Image:Wifiphone06.jpg\|center\|200px\|thumb\|By clicking on the Phonebook menu,
		+	you can Add new phone numbers or delete existing ones]]
		+
		+	In the Phonebook menu, we can add new numbers or delete the ones already listed there. We can also include multiple numbers for each person.
		+
		+	[[Image:Wifiphone07.jpg\|center\|200px\|thumb\|SIP Settings]]
		+
		+	In the SIP Settings tab, we can configure the IP address of the SIP Proxy, SIP Port (usually 5060), the IP address of the SIP Registrar (usually the same as that of SIP Proxy), Registrar Port (also usually 5060), and SIP account number consisting of telephone number and the password related. As for VoIP Rakyat SIP information, fill in the SIP Proxy and SIP Registrar with voiprakyat.or.id.
		+
		+	[[Image:Wifiphone08.jpg\|center\|200px\|thumb\|NAT Settings]]
		+
		+	In the NAT Settings menu, you can configure the Proxy address and Proxy Port. The Proxy address for VoIP Rakyat is voiprakyat.or.id. And the Proxy Port normally used is 5060.
		+
		+	[[Image:Wifiphone09.jpg\|center\|200px\|thumb\|The SIP-SDP Settings tab]]
		+
		+	In SIP-SDP Settings tab, we can configure several things related to the type of Codec, packet time, DTMF Relay, UDP Port and RTP Port. These parameters are good by default, so just leave them as is.
		+
		+	[[Image:Wifiphone10.jpg\|center\|200px\|thumb\|By clicking on the wireless tab of the administration panel, you can find out to which hotspot the phone is connected]]
		+
		+	In the Wireless section we can see to which Access Point the WiFi Phone is connected.
		+
		+	[[Image:Wifiphone11.jpg\|center\|200px\|thumb\|By clicking on the Administration tab of the administration panel, you can change your password]]
		+
		+	In administration section, we can set the administrator's username and related password for the WiFi Phone. The default configuration for username and password are both admin.

	==See Also==		==See Also==