PySIM - Revision history

Onnowpurbo: /* Tipe SIM Card */

2016-02-02T09:41:07Z

Tipe SIM Card

Onnowpurbo at 21:55, 29 April 2014

2014-04-29T21:55:53Z

Onnowpurbo at 12:58, 29 April 2014

2014-04-29T12:58:11Z

Onnowpurbo at 10:21, 29 April 2014

2014-04-29T10:21:30Z

Onnowpurbo at 10:14, 29 April 2014

2014-04-29T10:14:12Z

Onnowpurbo at 10:11, 29 April 2014

2014-04-29T10:11:51Z

Onnowpurbo: /* Lebih Detail */

2014-03-26T06:52:03Z

Lebih Detail

Onnowpurbo: /* Referensi */

2014-03-26T06:51:38Z

Referensi

Onnowpurbo at 03:13, 26 March 2014

2014-03-26T03:13:18Z

Onnowpurbo at 03:01, 26 March 2014

2014-03-26T03:01:32Z

@@ Line 119: / Line 119: @@
 Ini digunakan
-./pySim-prog.py  -p 0 -n OpenBTS -c 1 -x 001 -y 01 -j 4 -t grcardsim
+ ./pySim-prog.py  -p 0 -n OpenBTS -c 1 -x 001 -y 01 -j 4 -t grcardsim
 ==SIM Programming FAQ==

← Older revision		Revision as of 21:55, 29 April 2014
Line 1:		Line 1:
		+	[[Image:Smartcard-writer-bludrive2.png\|right\|200px\|thumb\|Smartcard Writer Bludrive II]]
		+
	pySIM adalah SIM card management tool, yang mampu untuk membuat, mengedit, men-delete, backup dan restore phonebook & SMS records.		pySIM adalah SIM card management tool, yang mampu untuk membuat, mengedit, men-delete, backup dan restore phonebook & SMS records.

← Older revision		Revision as of 12:58, 29 April 2014
Line 107:		Line 107:
	print sc.run_gsm('00112233445566778899aabbccddeeff')		print sc.run_gsm('00112233445566778899aabbccddeeff')

		+
		+
		+	==Tipe SIM Card==
		+
		+	Tampaknya ada beberapa tipe SIM Card
		+
		+	FakeMagicSim, SuperSim, MagicSim, GrcardSim, SysmoSIMgr1, SysmoUSIMgr1
		+
		+	Ini digunakan
		+
		+	./pySim-prog.py -p 0 -n OpenBTS -c 1 -x 001 -y 01 -j 4 -t grcardsim

@@ Line 5: / Line 5: @@
 * USB Serial device. Di UNIX akan terdeteksi sebagai /dev, seperti /dev/ttyUSB0. Contoh 16-in-1 Magic SIM.
 * PC/SC device. Device ini berhubungan melalui PC/SC driver dan tidak akan terlihat sebagai /dev. Jenis ini lebih banyak. Bluedrive II yang digunakan oleh RangeNetworks adalah jenis ini.
 Untuk melihat apakah smartcard writer terdeteksi dengan baik kita dapat menulis
@@ Line 14: / Line 13: @@
   Bus 003 Device 002: ID 1b0e:1078 BLUTRONICS S.r.l. BLUDRIVE II CCID
 Untuk mendukung operasi smartcard writer kita perlu menginstalasi
@@ Line 20: / Line 29: @@
 Setelah semua di instalasi, kita dapat memprogram SIM card dengan pysim.
-Gunakan opsi -p untuk menentukan PC/SC interface (biasanya "-p 0"),
+Gunakan opsi:
-dan untuk Range GR-Card blank SIM kita menset tipe card sebagai "-t grcardsim".
 Contoh:
@@ Line 37: / Line 49: @@
   Programming ...
   Done !
 Other comments on pysim:
@@ Line 47: / Line 65: @@
      that means the SIM is in the drive upside down or backwards.
 ==Lebih Detail==
@@ Line 122: / Line 106: @@
   # Run A3/A8
   print sc.run_gsm('00112233445566778899aabbccddeeff')
 ==Referensi==

← Older revision		Revision as of 10:14, 29 April 2014
Line 6:		Line 6:
	* PC/SC device. Device ini berhubungan melalui PC/SC driver dan tidak akan terlihat sebagai /dev. Jenis ini lebih banyak. Bluedrive II yang digunakan oleh RangeNetworks adalah jenis ini.		* PC/SC device. Device ini berhubungan melalui PC/SC driver dan tidak akan terlihat sebagai /dev. Jenis ini lebih banyak. Bluedrive II yang digunakan oleh RangeNetworks adalah jenis ini.

		+
		+	Untuk melihat apakah smartcard writer terdeteksi dengan baik kita dapat menulis
		+
		+	lsusb
		+
		+	Hasilnya kira-kira
		+
		+	Bus 003 Device 002: ID 1b0e:1078 BLUTRONICS S.r.l. BLUDRIVE II CCID

	Untuk mendukung operasi smartcard writer kita perlu menginstalasi		Untuk mendukung operasi smartcard writer kita perlu menginstalasi

← Older revision		Revision as of 10:11, 29 April 2014
Line 1:		Line 1:
−	~~About~~	+	pySIM adalah SIM card management tool, yang mampu untuk membuat, mengedit, men-delete, backup dan restore phonebook & SMS records.
		+
		+	SIM card di handphone adalah smartcard sederhana. Kita dapat mem-program SIM card menggunakan smartcard writer. Pada dasarnya smartcard writer ada 2 jenis, yaitu:
		+
		+	* USB Serial device. Di UNIX akan terdeteksi sebagai /dev, seperti /dev/ttyUSB0. Contoh 16-in-1 Magic SIM.
		+	* PC/SC device. Device ini berhubungan melalui PC/SC driver dan tidak akan terlihat sebagai /dev. Jenis ini lebih banyak. Bluedrive II yang digunakan oleh RangeNetworks adalah jenis ini.
		+
		+
		+	Untuk mendukung operasi smartcard writer kita perlu menginstalasi
		+
		+	sudo apt-get install libudev1 libpcsclite1 libccid python-pyscard
		+
		+	Setelah semua di instalasi, kita dapat memprogram SIM card dengan pysim.
		+	Gunakan opsi -p untuk menentukan PC/SC interface (biasanya "-p 0"),
		+	dan untuk Range GR-Card blank SIM kita menset tipe card sebagai "-t grcardsim".
		+	Contoh:
		+
		+	openbts@UnitC:~/pysim$ ./pySim-prog.py -p 0 -n OpenBTS -c 1 -x 001 -y 01 -j 4 -t grcardsim
		+	Failed to load symbol for: SCardCancelTransaction, /usr/local/lib/libpcsclite.so.1: undefined symbol: SCardCancelTransaction!
		+	Insert card now (or CTRL-C to cancel)
		+	Generated card parameters :
		+	> Name : OpenBTS
		+	> SMSP : 0015555
		+	> ICCID : 89010010100000000004
		+	> MCC/MNC : 1/1
		+	> IMSI : 001010000000004
		+	> Ki : bc9aecfabe1f81f1f85d09370f5a6f51
		+
		+	Programming ...
		+	Done !
		+
		+	Other comments on pysim:
		+
		+	The "undefined symbol" warning does not appear to be a problem, so ignore it.
		+	If you get the error message
		+
		+	smartcard.Exceptions.CardConnectionExc
		+	eption: Unable to connect with protocol: T0 or T1. Card is unpowered
		+
		+	that means the SIM is in the drive upside down or backwards.
		+
		+	Use of the Bludrive II:
		+
		+	Proper card orientation is with the metal contacts facing up, inside the device.
		+	When the SIM is inserted correctly, the LED on the unit will turn red for about ten seconds and then turn green again.
		+	If the SIM is not inserted correctly, the LED on the unit will flash red for about a second and then turn red and stay red until the SIM is removed.
		+
		+	SIM Programming FAQ
		+
		+	Q: Should all the sims have the same Ki ? Or is recomended that each sim has its own Ki?
		+	A: Every SIM needs a unique and random Ki. PySIM will generate a random Ki by default.
		+
		+	Q: What is the use of the "Name" in the sim?
		+	A: It is the "short name" for your phone company. It should be 8 characters or less to be displayed properly on most phones.
		+
		+	Q: What is the "SMSP"?
		+	A: "Short Message Service Parameters". Take a look at GSM 11.11 Section 10.5.6, attached. The default values provided by PySIM are OK if you don't want to worry with these.
		+
		+	Q: Why do all generated sims have "89" as the starting value of the ICCID?
		+	A: Take a look at http://en.wikipedia.org/wiki/Subscriber_Identity_Module#ICCID for an explanation of the ICCID fields. The "89" prefix is used for all SIMs. The next 2-3 digits are from the E.164 country code.

−	~~pySIM is SIM card management tool, capable of creating, editing, deleting, backup and restore operations on your SIM Phonebook and SMS records.~~
−	~~Requirements~~

	pySIM requires the following:		pySIM requires the following:

← Older revision		Revision as of 06:51, 26 March 2014
Line 65:		Line 65:
	* https://bitbucket.org/geekman/pysim		* https://bitbucket.org/geekman/pysim
	* https://bitbucket.org/geekman/pysim/src		* https://bitbucket.org/geekman/pysim/src
		+	* http://galaxyehacker.blogspot.com/2014/01/super-sim-sim-max.html

@@ Line 21: / Line 21: @@
 This utility allows to :
- * Program customizable SIMs. Two modes are possible:
+* one where you specify every parameter manually :
-  - one where you specify every parameter manually :
+ ./pySim-prog.py -n 26C3 -c 49 -x 262 -y 42 -i <IMSI> -s <ICCID>
-  - one where they are generated from some minimal set :
+ ./pySim-prog.py -n 26C3 -c 49 -x 262 -y 42 -z <random_string_of_choice> -j <card_num>
-./pySim-prog.py -n 26C3 -c 49 -x 262 -y 42 -z <random_string_of_choice> -j <card_num>
+With <random_string_of_choice> and <card_num>,
-    With <random_string_of_choice> and <card_num>, the soft will generate
+You also need to enter some parameters to select the device :
-  You also need to enter some parameters to select the device :
+ -t TYPE : type of card (supersim, magicsim, fakemagicsim or try 'auto')
-   -t TYPE : type of card (supersim, magicsim, fakemagicsim or try 'auto')
+ -d DEV  : Serial port device (default /dev/ttyUSB0)
-   -d DEV  : Serial port device (default /dev/ttyUSB0)
+ -b BAUD : Baudrate (default 9600)
- * Interact with SIMs from a python interactive shell (ipython for eg :)
+* Interact with SIMs from a python interactive shell (ipython for eg :)
-from pySim.transport.serial import SerialSimLink
+ from pySim.transport.serial import SerialSimLink
-from pySim.commands import SimCardCommands
+ from pySim.commands import SimCardCommands
-sl = SerialSimLink(device='/dev/ttyUSB0', baudrate=9600)
+ sl = SerialSimLink(device='/dev/ttyUSB0', baudrate=9600)
-sc = SimCardCommands(sl)
+ sc = SimCardCommands(sl)
-sl.wait_for_card()
+ sl.wait_for_card()
-	# Print IMSI
+ # Print IMSI
-print sc.read_binary(['3f00', '7f20', '6f07'])
+ print sc.read_binary(['3f00', '7f20', '6f07'])
-	# Run A3/A8
+ # Run A3/A8
-print sc.run_gsm('00112233445566778899aabbccddeeff')
+ print sc.run_gsm('00112233445566778899aabbccddeeff')

← Older revision		Revision as of 03:01, 26 March 2014
Line 15:		Line 15:

	pySIM source code is released under the GNU General Public License (GPL) and is available on SourceForge: pySim		pySIM source code is released under the GNU General Public License (GPL) and is available on SourceForge: pySim
		+
		+
		+	==Lebih Detail==
		+
		+
		+	This utility allows to :
		+
		+	* Program customizable SIMs. Two modes are possible:
		+
		+	- one where you specify every parameter manually :
		+
		+	./pySim-prog.py -n 26C3 -c 49 -x 262 -y 42 -i <IMSI> -s <ICCID>
		+
		+
		+	- one where they are generated from some minimal set :
		+
		+	./pySim-prog.py -n 26C3 -c 49 -x 262 -y 42 -z <random_string_of_choice> -j <card_num>
		+
		+	With <random_string_of_choice> and <card_num>, the soft will generate
		+	'predictable' IMSI and ICCID, so make sure you choose them so as not to
		+	conflict with anyone. (for eg. your name as <random_string_of_choice> and
		+	0 1 2 ... for <card num>).
		+
		+	You also need to enter some parameters to select the device :
		+	-t TYPE : type of card (supersim, magicsim, fakemagicsim or try 'auto')
		+	-d DEV : Serial port device (default /dev/ttyUSB0)
		+	-b BAUD : Baudrate (default 9600)
		+
		+	* Interact with SIMs from a python interactive shell (ipython for eg :)
		+
		+	from pySim.transport.serial import SerialSimLink
		+	from pySim.commands import SimCardCommands
		+
		+	sl = SerialSimLink(device='/dev/ttyUSB0', baudrate=9600)
		+	sc = SimCardCommands(sl)
		+
		+	sl.wait_for_card()
		+
		+	# Print IMSI
		+	print sc.read_binary(['3f00', '7f20', '6f07'])
		+
		+	# Run A3/A8
		+	print sc.run_gsm('00112233445566778899aabbccddeeff')