Format dan Set Harddisk Label - Revision history

Onnowpurbo: /* Pranala Menarik */

2012-03-29T13:04:08Z

Pranala Menarik

Onnowpurbo: /* Pranala Menarik */

2012-02-11T00:42:56Z

Pranala Menarik

Onnowpurbo at 00:38, 11 February 2012

2012-02-11T00:38:59Z

Onnowpurbo: /* Task: Label the partition */

2012-02-10T22:00:15Z

Task: Label the partition

Onnowpurbo at 06:24, 16 February 2011

2011-02-16T06:24:24Z

Onnowpurbo at 06:20, 16 February 2011

2011-02-16T06:20:19Z

Onnowpurbo: /* Pranala Menarik */

2011-02-16T06:18:00Z

Pranala Menarik

Onnowpurbo: New page: Q. I've installed a new 250GB SATA hard disk on our office CentOS Linux server. How do I format a hard disk under Linux operating system from a shell prompt? A.. There are total 4 steps i...

2011-01-03T05:46:29Z

New page: Q. I've installed a new 250GB SATA hard disk on our office CentOS Linux server. How do I format a hard disk under Linux operating system from a shell prompt? A.. There are total 4 steps i...

New page

Q. I've installed a new 250GB SATA hard disk on our office CentOS Linux server. How do I format a hard disk under Linux operating system from a shell prompt?

A.. There are total 4 steps involved for hard disk upgrade and installation procedure:

==Step #1 : Partition the new disk using fdisk command==

Following command will list all detected hard disks:
# fdisk -l | grep '^Disk'
Output:

Disk /dev/sda: 251.0 GB, 251000193024 bytes
Disk /dev/sdb: 251.0 GB, 251000193024 bytes

A device name refers to the entire hard disk. For more information see Linux partition naming convention and IDE drive mappings.
To partition the disk - /dev/sdb, enter:
# fdisk /dev/sdb
The basic fdisk commands you need are:

* m - print help
* p - print the partition table
* n - create a new partition
* d - delete a partition
* q - quit without saving changes
* w - write the new partition table and exit

==Step#2 : Format the new disk using mkfs.ext3 command==

To format Linux partitions using ext2fs on the new disk:
# mkfs.ext3 /dev/sdb1

==Step#3 : Mount the new disk using mount command==

First create a mount point /disk1 and use mount command to mount /dev/sdb1, enter:
# mkdir /disk1
# mount /dev/sdb1 /disk1
# df -H

==Step#4 : Update /etc/fstab file==

Open /etc/fstab file, enter:
# vi /etc/fstab
Append as follows:

/dev/sdb1 /disk1 ext3 defaults 1 2

Save and close the file.

==Task: Label the partition==

You can label the partition using e2label. For example, if you want to label the new partition /backup, enter
# e2label /dev/sdb1 /backup
You can use label name insted of partition name to mount disk using /etc/fstab:
LABEL=/backup /disk1 ext3 defaults 1 2

==Pranala Menarik==

* [[Format harddisk]]
* [[Linux Howto]]

[[Category: Linux]]

@@ Line 13: / Line 13: @@
   Disk /dev/sdb: 251.0 GB, 251000193024 bytes
-A device name refers to the entire hard disk. For more information see Linux partition naming convention and IDE drive mappings.
+Nama device menunjukan seluruh hardisk.
-To partition the disk - /dev/sdb, enter:
   # fdisk /dev/sdb
@@ Line 27: / Line 28: @@
 * w - write the new partition table and exit
-==Step#2 : Format the new disk using mkfs.ext3 command==
+==Step #2 : Format the new disk using mkfs.ext3 command==
 Untuk memformat partisi linux dapat menggunakan perintah
@@ Line 37: / Line 38: @@
   # mkfs.ext4 /dev/sdb1
-==Step#3 : Mount the new disk using mount command==
+==Step #3 : Mount the new disk using mount command==
 Menempelkan ke folder /disk1 menggunakan perintah mount /dev/sdb1, sebagai berikut:
@@ Line 45: / Line 46: @@
   # df -H
-==Step#4 : Update /etc/fstab file==
+==Step #4 : Update /etc/fstab file==
 Buka file /etc/fstab
@@ Line 73: / Line 74: @@
 * [[Linux Howto]]
 * [[Label harddisk]]
 [[Category: Linux]]

@@ Line 72: / Line 72: @@
 * [[Format dan Set Harddisk Label]]
 * [[Format harddisk]]
 * [[Linux Howto]]

@@ Line 57: / Line 57: @@
 Save and close the file.
-==Task: Label the partition==
+==Memberi Label Partisi==
   # e2label /dev/sdb1 /backup
-You can use label name insted of partition name to mount disk using /etc/fstab:
   LABEL=/backup /disk1 ext3 defaults 1 2
 ==Pranala Menarik==

@@ Line 1: / Line 1: @@
-Q. I've installed a new 250GB SATA hard disk on our office CentOS Linux server. How do I format a hard disk under Linux operating system from a shell prompt?
+Bagaimana cara memformat dan mengupgrade harddisk menggunakan shell? Berikut adalah empat (4) langkah yang perlu dilakukan,
-==Step #1 : Partition the new disk using fdisk command==
+==Step #1 : Partisi harddisk menggunakan perintah fdisk==
   # fdisk -l | grep '^Disk'
 Output:

@@ Line 14: / Line 14: @@
 A device name refers to the entire hard disk. For more information see Linux partition naming convention and IDE drive mappings.
 To partition the disk - /dev/sdb, enter:
   # fdisk /dev/sdb
 The basic fdisk commands you need are:
-    * m - print help
+* m - print help
-    * p - print the partition table
+* p - print the partition table
-    * n - create a new partition
+* n - create a new partition
-    * d - delete a partition
+* d - delete a partition
-    * q - quit without saving changes
+* q - quit without saving changes
-    * w - write the new partition table and exit
+* w - write the new partition table and exit
 ==Step#2 : Format the new disk using mkfs.ext3 command==
-To format Linux partitions using ext2fs on the new disk:
+Untuk memformat partisi linux dapat menggunakan perintah
   # mkfs.ext3 /dev/sdb1
 ==Step#3 : Mount the new disk using mount command==
-First create a mount point /disk1 and use mount command to mount /dev/sdb1, enter:
+Menempelkan ke folder /disk1 menggunakan perintah mount /dev/sdb1, sebagai berikut:
   # mkdir /disk1
   # mount /dev/sdb1 /disk1
@@ Line 38: / Line 46: @@
 ==Step#4 : Update /etc/fstab file==
-Open /etc/fstab file, enter:
+Buka file /etc/fstab
   # vi /etc/fstab
-Append as follows:
   /dev/sdb1               /disk1           ext3    defaults        1 2